Jumat, 19 Mei 2017

Input or input control equipment is a part of Light Gun and Light Pen Video Game AMNIMARJESLOW AL DO FOUR DO AL ONE LJBUSAF thankyume orbit


      

                                                        3 


Light Gun was first used for video games through the Shooting Gallery game by Magnafox Odyssey in 1972. The famous light gun version was produced by Nintendo, under the name NES Zapper or Beam Gun in Japan for Nintendo Entertainment System (NES). NES Zapper became famous with Duck Hunt game in 1985 in the US.

How to play it simple, just direct the target on the screen with the gun and press the trigger.

Ways of working

Light gun operation is quite simple, when light gun light is directed to the display, light gun will detect light through the photodiode in the sleeve of the gun.

At the same time the computer (game console) receives a signal from the screen driver (output). These signals consist of horizontal retrace and vertical retrace displays.  


    
                                     2 

Keep in mind that these two retrace (light beam) function as the composer of the image on the television (display). The light beam is an electron beam that crosses the screen from the left to where the movement of the electron beam is shown in the image below.
In the figure, the horizontal retrace shown by the blue line shows the electron-beam lines on the screen from left to right, while the vertical retrace shown by the red line indicates the file is being floated back (fly back) to the left. As the file reaches at the bottom of the right side, it moves back to the upper left corner of the screen.
The Screen driver sends the retrace signal to the computer, so the computer knows the position of the electron beam is in each frame.
When the player directs the object and pulls the trigger, the computer from the console will blacken the screen and the diode of the rifle will start receiving light. Then the computer emits a solid white block around the target where we target when firing. Photodiode on the zapper detects changes in light intensity and tells the computer that the photodiode is directed to the blocked target. When we shoot more than one target, the white block that appears surrounds the target shot at a time. Of course when playing this game we will not be aware because the incident lasted less than 1 second. 



                                                                         X  .  I  
                                                                   LIGHT  GUN  

 
                           Hasil gambar untuk Light gun electronics circuit 


A light gun is a pointing device for computers and a control device for arcade and video games, typically shaped to resemble a pistol.
Modern screen-based light guns work by building an optical sensor into the gun, which receives its input from the light emitted by on-screen target(s). The first device of this type, the light pen, was used on the MIT Whirlwind computer.
The light gun and its ancestor the light pen are now rarely used as pointing devices due largely to the popularity of the mouse and changes in monitor display technology—conventional light guns only work with CRT monitors.

  

  Sega Master System, Sega's The Light Phaser


A bright cloud



The first light guns appeared in the 1930s, following the development of light-sensing vacuum tubes. It was not long before the technology began appearing in arcade shooting games, beginning with the Seeburg Ray-O-Lite in 1936. These early light gun games, like modern laser tag, used small targets (usually moving) onto which a light-sensing tube was mounted; the player used a gun (usually a rifle) that emitted a beam of light when the trigger was pulled. If the beam struck the target, a "hit" was scored.
These games evolved throughout subsequent decades, culminating in Sega's Periscope, the company's first successful game released in 1966, which required the player to target cardboard ships. Periscope was an early electro-mechanical game, and the first arcade game to cost a quarter per play. Sega's 1969 game Missile featured electronic sound and a moving film strip to represent the targets on a projection screen, and their 1972 game Killer Shark featured a mounted light gun that shot at targets whose movement and reactions were displayed using back image projection onto a screen. Nintendo released the Beam Gun in 1970 and the Laser Clay Shooting System in 1973, followed in 1974 by the arcade game Wild Gunman, which used video projection to display the target on the screen. In 1975, Sega released the early co-operative light gun shooters Balloon Gun  and Bullet Mark.

        The Atari, Inc XG-1 Light Gun  




Use in video games

The video game light gun is typically modeled on a ballistic weapon (usually a pistol) and is used for targeting objects on a video screen. With force feedback, the light gun can also simulate the recoil of the weapon. The first gun for a home console was in fact a big rifle, the Magnavox Odyssey's Shooting Gallery, which looked very lifelike and even needed to be "cocked" after each shot.
Light guns are very popular in arcade games, but had not caught on as well in the home video game console market until after the Nintendo Entertainment System (NES), Sega Master System (SMS), Mega Drive/Genesis, Super Nintendo Entertainment System (SNES) systems and Atari XEGS. Many home 'Pong' systems of the 1970s included a pistol or gun for shooting simple targets on screen. Nintendo's NES Zapper for the NES, is the most popular example of the light gun, and Duck Hunt its most popular game.
Traditional light guns cannot be used on the newer LCD and plasma screens, and have problems with projection screens.
There are also light guns for Sega Saturn, Playstation and several other console and arcade systems. Recent light gun video games include Resident Evil: The Umbrella Chronicles, Time Crisis 4, Virtua Cop 3, and The House of the Dead: Overkill.
In 2007, Nintendo released the Wii Zapper for the Wii, a peripheral which is actually a plastic shell that houses both the Wii Remote and nunchuk for gun-style video games. While it does not contain any traditional light gun technology, the peripheral makes use of the Wii Remote's built-in infrared tracking system to shoot targets that correspond on-screen. Its name is a reference to the classic NES Zapper for the Nintendo Entertainment System. Sony have also released attachments that house the PlayStation Move motion controller in the form of a pistol and rifle, the latter named the Sharp Shooter.
Namco's GunCon 3 also uses an infrared optical sensor system similar to the Wii Remote.

Design

The "light gun" is named because it uses light as its method of detecting where on screen the user is targeting. The name leads one to believe that the gun itself emits a beam of light, but in fact most light guns actually receive light through a photodiode in the gun barrel.
There are two versions of this technique that are commonly used, but the concept is the same: when the trigger of the gun is pulled, the screen is blanked out to black, and the diode begins reception. All or part of the screen is painted white in a way that allows the computer to judge where the gun is pointing, based on when the diode detects light. The user of the light gun notices little or nothing, because the period in which the screen is blank is usually only a fraction of a second .

Sequential targets

The first detection method, used by the Zapper, involves drawing each target sequentially in white light after the screen blacks out. The computer knows that if the diode detects light as it is drawing a square (or after the screen refreshes), then that is the target at which the gun is pointed. Essentially, the diode tells the computer whether or not the player hit something, and for n objects, the sequence of the drawing of the targets tell the computer which target the player hit after 1 + ceil(log2(n)) refreshes (one refresh to determine if any target at all was hit and ceil(log2(n)) to do a binary search for the object that was hit).
A side effect of this is that on poorly designed games, often a player can point the gun at a light bulb or other bright light source, pull the trigger, and cause the system to falsely detect a hit on the first target every time. Better games account for this either by detecting if all targets appear to match or by displaying a black screen and verifying that no targets match.

Cathode ray timing

The black GunCon made by Namco for the PlayStation. 

The blue (top) and pink (middle) Konami Justifiers made for the Super Nintendo Entertainment System and the green (bottom) one made for the PlayStation 

The second method, used by the Super Nintendo Entertainment System's Super Scope and computer light pens, is more elaborate and more accurate.
The trick to this method lies in the nature of the cathode ray tube inside the video monitor (CRTs were the only affordable TV monitors in the late 1980s and early 1990s, when this method was popularized). The screen is drawn by a scanning electron beam that travels across the screen starting at the top until it hits the end, and then moves down to update the next line. This is done repeatedly until the entire screen is drawn, and appears instantaneous to the human eye as it is done very quickly.
When the player pulls the trigger, the computer (often assisted by the display circuitry) times how long it takes the electron beam to excite the phosphor at the location at which the gun is pointed. The light gun sends a signal after sensing the sudden small change in brightness of a point on the screen when the electron gun refreshes that spot. The computer then calculates the targeted position based on the monitor's horizontal refresh rate (the fixed amount of time it takes the beam to get from the left to right side of the screen). Either the computer provides a time base for the horizontal refresh rate through the controller's connector (as in the Super Scope), or the gun reads the composite video signal through a T-connector on the A/V cable (as in the GunCon 2). Once the computer knows where the gun is pointed, it can tell through collision detection if it coincides with the target or not.
Many guns of this type (including the Super Scope) ignore red light, as red phosphors have a much slower rate of decay than green or blue phosphors. As a result, some (but not all) games brighten the entire screen's green/blue pixels somewhat when the trigger is pulled in order to get a more reliable fix on the position.
Display timing is not possible with plasma, LCD, and DLP monitors, since they do not have an "off" state between refreshes. Their digital signal processing electronics also may introduce a nontrivial lag between the signal input and display output, which is not predictable because it varies between monitor models and brands and even between mode settings of a single monitor. A lag which is not very significant for player feedback may be enough to completely destroy the accuracy of a display-timing based light gun system.

Combined method

Some light guns designed for sequential targeting are not timed precisely enough to get an (X, Y) reading against the video signal, but they can use a combination of the two methods. First the screen is brightened and the response time is measured as in cathode ray timing, but the computer measures only which scanline was hit and not which horizontal pixel was hit. This does not need nearly as fast a timer that pure cathode ray timing uses, on the order of 15 kHz for Y vs. 5 MHz for (X, Y) on a standard resolution display. Then using sequential targets, the game cycles among those targets on the line.

Infrared emitters

A new method was developed to compensate for display technologies other than CRT. It relies on one or several infrared light emitters placed near the screen, and one IR sensor on the muzzle of the gun. When the trigger is pressed, the gun sends the intensity of the IR beam it detects. Since this intensity depends upon both distance and relative angle to the screen, angle sensors are located in the gun. This way a trigonometric equation system is solved, and the muzzle's 3D position relative to the screen is calculated. Then, by projecting the muzzle on the screen with the measured angles the impact point is determined. An early example of this technology (though not using IR) can be seen in the NES Power Glove Accessory, which used three ultrasonic sensors serving the same function as the IR emitters used in some lightguns.
A simpler variant is commonly used in arcades, where there are no angle detectors but 4 IR sensors. However, this can prove inaccurate when shooting from certain distances and angles, since the calculation of angles and 3D position has a larger margin of error.
Other variants include 3 or more emitters with different infrared wavelengths and the same number of sensors. With this method and proper calibration three or more relative angles are obtained, thus not needing angle detectors to position the gun.
Sometimes, the sensors are placed around the screen and the emitter on the gun, but calculations are similar.
The Wii Remote uses an infrared video camera in the handheld controller, rather than a simple sensor.
This family of methods are used for the Wii Remote, GunCon 3, and modern arcade light gun games.

Image capture

When the user pulls the trigger the screen is replaced for a split-second with a seemingly random display of black and white pixels, or groups of pixels (blocks). The light gun contains a fine-resolution but low pixel count digital camera with a very narrow field of view. With just a handful of the encrypted random dot image pixels captured, the gun converts the small image into a binary array which allows the computer to locate the exact position the gun was pointed at. This method is compatible with any screen of any size. The size of the screen and distance to shooter is entered into the gun driver software to determine the dimensions of the random blocks/pixels to best allow rendering on the light gun CCD.

Multiplayer

A game that uses more than one gun reads both triggers continuously and then, when one player pulls a gun's trigger, the game reads that gun until it knows which object was hit.

Positional guns

Positional guns are fairly common in video arcades. A positional gun is a gun mounted to the cabinet on a swivel that allows the player to aim the gun. These are often confused with light guns but work quite differently. These guns may not be removed from the cabinet like their optical counterparts, which are tethered and stored in a mounted holster. They are typically more expensive initially but easier to maintain and repair. Games that use positional guns include Silent Scope, the arcade version of Resident Evil Survivor 2, Space Gun, Revolution X, and Terminator 2: Judgment Day. Console ports sometimes use light guns.
A positional gun is essentially an analog joystick that records the position of the gun to determine where the player is aiming on the screen. The gun must be calibrated, which usually happens after powering up. Early examples of a positional gun include Sega's Sea Devil in 1972, Taito's Attack in 1976 and Cross Fire in 1977, and Nintendo's Battle Shark in 1978. Some games, however, have mounted optical guns, such as Exidy's Crossbow.


                                                                X  .  II
                                                           LIGHT PEN 

Light pen


Photo of the Hypertext Editing System (HES) console in use at Brown University, circa October 1969. The photo shows HES on an IBM 2250 Mod 4 display station, including lightpen and programmed function keyboard, channel coupled to Brown's IBM 360 mainframe.
A light pen is a computer input device in the form of a light-sensitive wand used in conjunction with a computer's CRT display.

It allows the user to point to displayed objects or draw on the screen in a similar way to a touchscreen but with greater positional accuracy. A light pen can work with any CRT-based display and other display technologies, but its ability to be used with LCDs was unclear (though Toshiba and Hitachi displayed a similar idea at the "Display 2006" show in Japan).
A light pen detects a change of brightness of nearby screen pixels when scanned by cathode ray tube electron beam and communicates the timing of this event to the computer. Since a CRT scans the entire screen one pixel at a time, the computer can keep track of the expected time of scanning various locations on screen by the beam and infer the pen's position from the latest timestamp. 

                      Hasil gambar untuk rangkaian elektronika senapan cahaya pada game

 

A bright cloud

The first light pen was created around 1955 as part of the Whirlwind project at MIT.
During the 1960s light pens were common on graphics terminals such as the IBM 2250, and were also available for the IBM 3270 text-only terminal.
Light pen usage was expanded in the early 1980s to personal computers such as the Fairlight CMI, and the BBC Micro. IBM PC compatible CGA, HGC and some EGA graphics cards also featured a connector for a light pen, as did early Tandy 1000 computers, the Thomson MO5 computer family, the Atari 8-bit and Commodore 8-bit home computers.
Because the user was required to hold their arm in front of the screen for long periods of time (potentially causing "gorilla arm") or to use a desk that tilts the monitor, the light pen fell out of use as a general purpose input device.   


                                                                         X  .  III
                                                       How a Rifle In Game Works 

  
              https://kutupedia.files.wordpress.com/2014/07/time-crisis-machine.jpg  

Video game games today are very popular with many people, especially children and adolescents. Even today, there are so many play arenas that provide various types of video games. One of the popular games is the use of light rifles used to shoot targets that are inside the screen. One of the game consoles that uses light rifle instruments is Time Crisis. In the game, when you aim the shotgun at the target on the screen and pull the trigger, the target shot on the screen will explode. You may be one of the fans of this game. But do you know how this game works? 


To create this effect, the shotgun is given a photodiode (phototransistor) on its barrel. Photodiode is able to capture the light coming from the screen. The rifle also has a trigger button connected to the computer for controlling the game. 


                                                        pernahkan menggunakan senjata ini dalam game yang anda mainkan, ini yang Dr.B namakan senapan cahaya. :P       

     Hasil gambar untuk Light gun electronics circuit
The computer receives a horizontal and vertical line-tracking signal from the electronic display so that it can see where the electrons are on the screen. Computers generally use one of two different techniques to ascertain whether the rifle is aimed at the target object firing when the trigger is pulled.  

                                    Hmm, Sini Dr. B kasi liat, ini namanya Fotodiode, ingat dan jangan lupa ya, :D

     The first method is, When you pull the trigger, the computer empties the screen for one frame. Then just color the target object shot on the screen (as a white object). When the photodiode captures the darkness after a vertical line and light tracer signal in a sequence, the computer assumes that the rifle is aimed at the object on the screen and gives the shot value.  


 
     Entahlah, apakah game ini mendidik atau malah menciptakan banyak pembunuh, tapi ingat pesan Dr. B ketika masih dapat dinikamati kenapa tidak? HAHA 

The second method is, the Computer empties the screen, then color the entire screen with white. Electronic highlighters take time to keep track of the entire screen when giving white. By comparing signals coming from photodiodes with horizontal and vertical tracking signals, the computer can detect where the electrons emit on the screen when the first photodiode senses there is light. The computer calculates the number of seconds passing between the time when the horizontal and vertical line tracking signal starts and when the first photodiode captures the presence of light. In a matter of microseconds the sensor tells the computer exactly where the rifle is aimed at the screen. If the calculation of positions and shoot targets is appropriate, the computer will give the shot value. 


         tembak daku kau ku cium # Ogaah.  


                                  Hasil gambar untuk Light gun electronics circuit  



                                                                       X  .  IIII 
 

                  Sega Light Phaser to Atari XG-1 Adapter  

The Sega Master System was released in 1986 in North America. It came with a light gun called the Sega Light Phaser. In 1987 Atari released the XE Game System, which is technically a repackaged Atari 8 bit computer with a detachable keyboard and it was marketed as a video game console. It also came with a light gun, the Atari XG-1.
Both systems were the direct competitors of the Nintendo Entertainment System (NES), which started its life in 1983 as the Nintendo Family Computer in Japan, and was later redesigned and released in the rest of the world as the NES in 1985.
The NES came with a light gun known as the NES Zapper and a pack-in game Duck Hunt, which used the light gun. As direct competitors, Atari and Sega’s offerings also came with light guns and light gun games.
While Nintendo’s gun is a simple light detector, both Atari and Sega guns are specialized light pens. They work by detecting the passing of the electron beam in front of their sights, sending an electric pulse to the computer when this happens, allowing it to determine the exact screen coordinates where the gun is pointed at. Sega games like Shooting Gallery take advantage of this superior detection method by displaying bullet holes on the background to represent your misfired shots in their exact positions. Nintendo’s gun can only detect if you’ve hit the (lit up) target, and nothing else .

Adapting light guns between systems

While Nintendo’s Zapper works on a simpler principle than their Atari and Sega counterparts, both Atari and Sega light guns work on the same “light pen” principle with only minor differences in their mode of operation, making possible to adapt a Sega gun for Atari operation and vice versa.
This is nothing new, there’s this article which shows you how to adapt a Sega Light Phaser to an Atari system, by rewiring the Sega gun connector to satisfy the Atari pinout. But there are two problems with it:
  • The article provides the pin numbers for the Atari side, but only the wire colors on the Sega side. I opened up my Sega Light Phaser only to find out that the wire colors were completely different to the ones on the article!
  • Due to differences between the Atari and the Sega system, when adapting a particular light gun for use on the opposite system, the trigger’s action will be reversed (the gun will fire when you release the trigger, or it will keep firing and only stop when the trigger is held down, depending on the game). The article suggests opening up the gun and rewiring the trigger microswitch to use the Normally Closed (NC) contacts instead of the usual Normally Open (NO). While it’s a perfectly valid solution, it requires modification of the gun itself. Once again, I opened up my Sega Light Phaser only to find out that the trigger microswitch is missing the NC terminal!
With these problems in mind, I had to look up for my own solution to the problem. I didn’t want to modify the gun itself, and also I’d need to come up with something to correct the “reversed trigger” problem without replacing the microswitch.

Sega to Atari Light Gun Adapter

First I traced the pinouts on both sides in order to adapt the correct signals using a pair of DE-9 connectors. Besides power and ground, the Sega Light Phaser uses two special pins called TL and TH for communication with the console. TL is the trigger microswitch connection. When the trigger is pulled, TL is tied low, with no internal pull-up inside the light gun. TH carries the light pen pulses.
In the Atari side of things, the trigger switch is read by the Joystick Up signal and the light pen pulses are read by the Joystick Fire signal. Therefore, TL must be hooked to Up and TH to Fire. This will get your Sega gun working in Atari light gun games, but there’s still the problem of the inverted trigger action.
The Atari expects a logically inverted signal for its gun trigger. A simple NOT gate would solve the problem, but I think it’s pretty wasteful to use a 7404 or similar hex inverter IC just for one of its NOT gates, not to mention the increased size and complexity of the circuit. My goal was to create a simple adapter with the lowest number of additional components, something that can be neatly built inside the D-connector housing. I came up with a single transistor inverter to correct the reversed trigger problem. Here’s the final schematic:
A single small signal NPN transistor inverts the trigger’s logic state, and a single 10k resistor provides the necessary pull-up to correctly bias the transistor’s base. The Atari’s joystick inputs already include internal pull-up resistors, making them unnecessary on the collector side.
Now the circuit is simple enough to be built inside a D-connector housing, allowing the construction of a simple and clean light gun adapter using two DE-9 connectors.
This is my finished adapter prototype. One day I might tuck it all neatly inside a plastic housing, but then again, laziness is my middle name…
Quick 'n Dirty Light Gun Adapter
It works just as expected. The trigger action is fully corrected and it works perfectly on the Atari system just like it does on the Sega Master System. I tested it out with my two light gun enabled XE game cartridges: Barnyard Blaster and Crossbow.
Some Barnyard Blaster action
The opposite conversion (Atari gun to Sega system) can be done just as easily by building the same circuit but reversing the pinout on both sides. I haven’t tried the XG-1 myself but several sources on the Internet cite the Sega Light Phaser as being much more accurate. Either way, happy retro gaming!

                                          Hasil gambar untuk rangkaian elektronika senapan cahaya pada game     

                                                            Light gun electronics circuit  


                           
                    Hasil gambar untuk Light gun electronics circuit  Hasil gambar untuk rangkaian elektronika senapan cahaya pada game
                               Hasil gambar untuk rangkaian elektronika senapan cahaya pada gameHasil gambar untuk rangkaian elektronika senapan cahaya pada game
 


                                                                        X  .  IIIII 
                                                       Make A High-Lighter Stun-Gun  

 

Xample The real Stun-Gun

In this article, I'll show you how to make a small, weaponized highlighter. Before I get into how to built this device, let me warn you. This device is harmful! When used, it can cause burns and/or serious muscle spasms. The voltage is potentially deadly! DO NOT attempt to build this device unless you are experienced with safety, electronics, soldering, and understand circuit schematics. 

Step 1 The Materials

  1. A Highlighter
  2. A disposable Kodak camera
  3. One 300V 10uf-80uf capacitor
  4. Rechargeable AA battery
  5. Miscilanious wire
  6. A temporary switch
  7. Two needles (sewing needles work fine)
  8. Hot glue
  9. Electrical tape

Step 2 The Tools

  1. Hot glue gun
  2. Wire cutters
  3. Soldering iron
  4. Solder
  5. Hot  glue gun
  6. Flux (unless you have flux-core solder)

Step 3 The Procedure

  1. First, dismantle the disposable camera and discharge the capacitor. Using the photo below, locate the large, black battery-like cilendar, and cross the two prongs with a screw driver. This is for safety purposes, since the capacitor can hold a charge for long periods of time, and electrocute you if you complete the short with your fingers. 
How To Make A High-Lighter Stun-Gun
2. Dismantle the highlighter. Take out the ink and felt tip and dispose of them.
3. The circuit is quite simple, consisting of the transformer, transistor, resistor, and diode from the camera circuit. Follow these steps to create the circuit, or the schematic below (circuit must be made standalone, with NO protoboard).
Note: If following the instructable guide, replace the film capacitor used with the one from the camera circuit/other (purchased online). Also, If the capacitor from your camera circuit is under 80uf (just look on the side of the capacitor, it should say. If not, don't risk it), you can use it in place of the capacitor on the taser.
How To Make A High-Lighter Stun-Gun
Ensure the final circuit is as small as possible. It should look similar to this (the little black battery-like object in the top right corner is the capacitor):
How To Make A High-Lighter Stun-Gun
4.  To build the switch and battery, take your temporary button and solder two, three inch long wires to the prongs of the switch. Next, melt two holes in the bottom cap of the highlighter. insert the wires, then glue the switch to the outside of the cap (see image below). Solder one switch-wire to the positive side of the battery (see image below, black object in top right. Similar in looks to a capacitor but without the white line). Solder the second switch wire to the positive of the transformer circuit. Cut a one inch piece of wire and solder it from the battery's negative to the transformer circuit's negative.

Note: I used a different type of battery, but AAs work just as well.
How To Make A High-Lighter Stun-Gun
5.  Cut two, two inch long wires and solder them to the capacitor. Next, locate the diode and ground portion of your circuit (note: The capacitor is already shown on the schematic). Ensure the polarity is correct (the diode connects to the little white line on the capacitor, or negative prong). Now, take the needles mentioned earlier and cut off any "end-nub" part of the needle. Solder the needles to the capacitor like this:

Note the small piece of electrical tape on the end of the capacitor. This is important to prevent shorting, do not forget it.

How To Make A High-Lighter Stun-Gun
The layout of the highlighter insertion (in order from bottom to top) should be:
  1. The switch
  2. The battery
  3. The transformer
  4. The capacitor
  5. The prongs
It should look something like this when built correctly:
How To Make A High-Lighter Stun-Gun
7. Test it, ensure it works properly. When the trigger button is pressed, a high frequency "weeing" should be heard. After a second, short the two prongs with a screw driver, if working properly, there should be a spark. Be careful! Don't shock yourself.

7. Once soldered and tested, carefully insert it into the highlighter case. The capacitor should fit all the way into the top portion of the case, and the needles should stick out of the end about half an inch. Inject hot glue into the top end, and aline the prongs (needles) so that they are in the center of the pen-hole (do all of this before the hot glue dries). Allow the glue to dry, and carefully insert the rest of the circuit. The transformer unit should fit in sideways, like this:
How To Make A High-Lighter Stun-Gun
8. Clip in the end cap, and your done! The battery should last a good 2000 charges, so there shouldn't be a need to recharge for a long time. When necessary, just pop off the end cap and charge the battery. To use, pull off the cap, press the button on the bottom, and short the two needles. Before you test it on people, get their permission first, unless they're occupied in attacking you.

attention :

  • If you solder it all together and it doesn't work, first check for polarity issues, then your circuit itself.
  • Ensure you cut enough wire to make the entire circuit easy to insert, but not too long, otherwise space issues will occur.
  • Don't cram!! If it doesn't fit, take it out and change the length of the wire  

                      Hasil gambar untuk Light gun electronics circuit   





  



Kamis, 18 Mei 2017

Signal tracer to seek interference and damage to audio and video electronics circuits as like Detector so do crystal pulsed as code for US AMNIMARJESLOW AL DO FOUR DO AL ONE LJBUSAF thankyume orbit


           Signal tracer To seek interference and damage to audio and video electronics circuits

                           

Hasil gambar untuk pelacak sinyal mendeteksi kerusakan rangkaian TV 
Simple signal tracking circuit 

  PACO Z-80 signal tracer probe       
Hasil gambar untuk signal tracer circuit

The signal tracker consists of a detector (taking back the low frequency of the high frequency carrier) and an ear phone. This signal tracker is used to search for circuit breakage by using the ear - phone.
By tracing the circuit from start-up to end-level by using a signal tracer earphone, the principle works like a medical device that is a stethoscope to examine the human body, with this signal tracker detectable which circuit level is damaged, by drawing conclusions from the inactivity of the earphone It, also this tracker can be used to look for damage to the sound circuit, where the test signal is disrupted. 



When and how to use signal-tracing techniques  ? 
Xample signal tracing to simple amplifier :  

                                               

By comparing the Vi and Vo readings, we can determine the strengthening. This method is also called Input-Output Method / Output-Input Method.
     By changing the output amplitudes of the signal generator, we can see whether the amplifier is linear in the input signal region.
     With the load impedance variation (RL), we can see whether the linear gain on the load changes.
     By changing the frequency of the signal generator, we can determine the frequency response of the amplifier.

With this simple arrangement, the important characteristics of the amplifier can be measured by the signal-tracing system, at amplitude and frequency, from input to amplifier output.

In some electronic devices, external signaling is not always necessary, especially when the signal that should exist on the equipment can be easily known. This method is called passive signal-tracing method . 



Xample Passive Tracing Signal Method A Power Supply :
  

  
                        Hasil gambar untuk block diagram simple power supply foto 

The mesh voltage is measured with an AC voltmeter on the wall outlet, on the fuse, and on the switch. If there is a 220 V AC voltage at the primary end of the transformer, then it is certain that the plug, cable, fuse and switch are in good condition.
    
AC signal on the secondary of the transformer can be measured on each side (secondary of transformer no CT) to ground. If there is a voltage on the secondary transformer of appropriate magnitude, then it can be ascertained that the transformer is in good condition.
    
Next, use the meter switch on the DC scale. Measure the voltage on C1 and on C2. If there is no DC voltage on C1 or C2, it means that the capacitor is short-circuited. When the L winding is open, then there is only a DC voltage at C1, but not in C2. When C1 and C2 are open (break), or when CR1 and CR2 directors are open, or both are short-circuited, the measured DC voltage is incorrect. Under such conditions, it is necessary to measure resistance to ensure the damaged component.
    
The second way is the opposite of the first way, ie starting from the measurement of DC voltage on capacitor C2, followed by measurement of DC voltage on capacitor C1 and so on. The result is the same because the measurement uses only voltmeter only.  



The following example is an FM radio whose block diagram shown in figure  does not work. 
 Hasil gambar untuk block diagram FM radio foto

 Examination of power supply and voltage at static state of the circuit has been done. The damage is in the area between the antenna and the audio amplifier. In the passive method, normal signals are considered to be present or known. However, since the antenna and tuning (which are thought to give normal signals to the system) are within the system itself, external signals must be assigned as normal signals and use speakers as signal indicators. This method is called an active signal-tracing method or signal injection. 


First step:

    
The signal generator is connected to the RF tuner, and the antenna is removed; The signal generator and tuner are set at the same frequency. If you do not hear anything on the loudspeaker, move the signal generator at point A. change the frequency of the generator signal at 10.7 MHz (Standard for FM radio). When the sound is heard (tone of the generator signal), this means damage to the RF tuner.
    
If not heard something, move the generator signal to the amplifier output, ie at point B. At this point, the amplitude of the generator signal must be increased to compensate for the gain of the middle amplifier.
    
At point C, the normal signal is an audio signal. Therefore, the signal generator entered through this point must be at the audio frequency.
    
At point D the generator signal should be strong enough to drive the loudspeaker. The loudspeaker can be tested by checking the voltage on the amplifier driver and minimizing it momentarily with the corresponding resistor between voltage and ground. This should generate a click sound on the loudspeaker. 


   
The second way:

     The check is done from the speakers to the tuner. To determine whether using the first or second way can be preliminary, for example: by briefly amplifying the audio amplifier input with ground using a screwdriver or the end of a clip, this should produce a loudspeaker click (if the loudspeaker and audio amplifier are working properly).
     If you do not hear the sound, then the second way is the best choice, because the damage must exist between the loudspeaker and the audio amplifier.
     When you hear a click, you can still continue the examination in a second way from point C, or in the first way, since both have the same chance of checking speed.

Means:
The signal-tracing method requires input signals on the suspect area, and can be measured accurately. Signal-tracing always requires at least one test kit and generally two.  



Methods of voltage and resistance

    
In general, voltage and resistance measurements are performed to check for suspected damaged tissue or components. Voltage measurements require equipment with ON conditions, whereas resistance measurements are made when the equipment is OFF.
    
Usually circuit diagrams and datasheets indicate the voltage required for normal operating conditions at a particular test point. By making such measurements, usually the location of damage to the network and components can be known.
    
Resistance measurement is a very useful method for checking electronics components. A simple resistance measurement can be used to ensure continuous wiring, the correct value approach of the transformer, inductor, winding as well as the value approach of the large capacitor.
    
The majority of resistors used in electronic equipment are carbon composition types and they tend to change in value due to age and heat. When this happens often perhaps the measurement of resistor resistance or other components in the circuit, should be assured by examination on the circuit image. The parallel impedance does not give an incorrect measurement, when a resistor increases in magnitude or open, it is relatively simple to determine this.
Voltage and Barrier Techniques are often used anywhere after the symptom-function technique refers to a particular circuit or component as a source of damage, or when a signaltracing technique has localized a defect in this way.
mean :Voltage and Barrier methods are used to pinpoint a component or circuit breakage and generally require company data for component and voltage values. 



The half-splitting method

     This method is suitable for series with series blocks / open loop system  (elongated) because it will be very fast when looking for damage. For example: function generator circuit, radio transmitter / receiver, etc.
     The step: starting from the center of the system, and successively on each of the middle half of the part of the system that has been separated until it is found to be damaged. 


 Block 1 ---> block 2 ---> block 3 ---->block 4 ----->block 5 ----> block 6 ----> block 7 ----> block8

 
As an insight material that in the electronics block diagram shows the signal flow, while the schematic circuit shows the flow of current and voltage, flow chart is the flow of the program or function. 


8 Block Sub Serial System Series
    
Check the output of block 4, if it works fine, means blocks 1 through 4 there is no problem.
    
If it does not work, then check block 2 output (middle of blocks 1-4), and if good means check out block 3 output, and if good means block 4 is damaged.
    
Check Output of block 8, if it works well, means block 5 to block 8 is no problem.
    
If it does not work, then check the output of block 6 (middle of blocks 1-4), and if good means check out the output of block 7, and if good, then block 8 is damaged.
Loop breaking method
    
Electronic systems or sub-systems with feedback, very difficult to trace the damage without breaking the loop. Appropriate DC voltage or signal, shall be injected at the point where the loop is disconnected.
    
Voltages and signals through the circuit, should be used to monitor errors.
    
Inverted voltage or signal can be changed, to see the change of circuit response from normal state.
    
Typically, the loop is broken at the point where the signal is at small power, so it can be injected properly. 



This technique can be used for example on a PLL (phase lock loop), such as :  

        

    Hasil gambar untuk block diagram PLL ( phase locked loop )  foto


 The power supply and reference oscillator output should be checked first before the loop is disconnected. In this case the output should be abnormal or unstable or missing, so we can be sure that the VCO is not good. Next we can do the loop termination at the appropriate point. So the loop termination here is not necessarily the feedback section, but is sought in small signal areas that are easily injected with existing equipment.
Substitution method

     In this method it is usually necessary to sold or replace parts as the final stage of the damage tracking process.
     There are two main stages in the substitution method that must be done, namely: use the correct replacement components, and connect correctly to the circuit.
     Prior to the replacement, it is advisable to check with other methods as described previously, to be sure which component is damaged.  



Do a voltage measurement to make sure that the voltage that is supposed to exist really exists. The voltage checks performed on the combined components of resistors and capacitors, will be able to show whether they are damaged or just one of them.
In practice, we are usually very difficult to find a replacement component in the form of ICs, transistors, and diodes that exactly match the replaced components. To solve this, you need to find equivalent data of IC type, transistor, or diode in semiconductor user manual.
If the replaced component has a special type, for example: transformer, coil-deflection yoke, and other special components, it is necessary to look for a completely suitable replacement component (no equivalent). 


                                                Hasil gambar untuk block diagram PLL ( phase locked loop )  foto  


  PRINCIPLE OF DAMAGE TRACK / FAILURE
1. Maintenance Process in Industry
2. Specifications
3. Reliability and Failure
4. Method-Tracking Method of Damage 

5. Problem-Solving Analysis
6. Active Component Testing
7. Circuit Checking and Testing  



                                                                        X  .  I  
                     

                   Detector (radio)  / tracker 

                     Gambar terkait

In electronics, a detector is an older term for an electronic component in a radio receiver that extracts information contained in a modulated radio wave, a demodulator. The term dates from the first three decades of radio (1886-1916). Unlike modern radio stations which transmit sound (an audio signal) on the radio carrier wave, the first radio transmitters transmitted information by wireless telegraphy, using different length pulses of radio waves to spell out text messages in Morse code. So early radio receivers did not have to extract an audio signal (sound) from the incoming radio signal, but only detect the presence or absence of the radio signal, to produce clicks in the receiver's earphones representing the Morse code symbols. The device that did this was called a detector. A variety of different detector devices, such as the coherer, electrolytic detector, and magnetic detector, were used during the wireless telegraphy era.
After sound (amplitude modulation, AM) transmission began around 1920, the term evolved to mean a demodulator, a nonlinear rectifier (usually a crystal diode or a vacuum tube) which extracted the audio signal from the radio frequency carrier wave. This is its current meaning, although modern detectors usually consist of semiconductor diodes, transistors, or integrated circuits.
In a superheterodyne receiver the term is also sometimes used to refer to the mixer, the tube or transistor which converts the incoming radio frequency signal to the intermediate frequency. The mixer is called the first detector, while the demodulator that extracts the audio signal from the intermediate frequency is called the second detector.

                                               

                                    A coherer detector, useful only for Morse code signals.

Amplitude modulation detectors

Envelope detector

 
A simple envelope detector 

A simple crystal radio with no tuned circuit can be used to listen to strong AM broadcast signals 

One major technique is known as envelope detection. The simplest form of envelope detector is the diode detector that consists of a diode connected between the input and output of the circuit, with a resistor and capacitor in parallel from the output of the circuit to the ground to form a low pass filter. If the resistor and capacitor are correctly chosen, the output of this circuit will be a nearly identical voltage-shifted version of the original signal.
An early form of envelope detector was the cat's whisker, which was used in the crystal set radio receiver. A later version using a crystal diode is still used in crystal radio sets today. The limited frequency response of the headset eliminates the RF component, making the low pass filter unnecessary. More sophisticated envelope detectors include the plate detector, grid-leak detector and transistor equivalents of them, infinite-impedance detectors (peak detector circuits), and precision rectifiers.

Product detector

A product detector is a type of demodulator used for AM and SSB signals, where the original carrier signal is removed by multiplying the received signal with a signal at the carrier frequency (or near to it). Rather than converting the envelope of the signal into the decoded waveform by rectification as an envelope detector would, the product detector takes the product of the modulated signal and a local oscillator, hence the name. By heterodyning, the received signal is mixed (in some type of nonlinear device) with a signal from the local oscillator, to give sum and difference frequencies to the signals being mixed, just as a first mixer stage in a superhet would produce an intermediate frequency; the beat frequency in this case, the low frequency modulating signal is recovered and the unwanted high frequencies filtered out from the output of the product detector.
Product detector circuits are analog multipliers and so essentially ring modulators or synchronous detectors and closely related to some phase-sensitive detector circuits. They can be implemented using something as simple as ring of diodes or a single dual-gate Field Effect Transistor to anything as sophisticated as an Integrated Circuit containing a Gilbert cell.

Frequency and phase modulation detectors

AM detectors cannot demodulate FM and PM signals because both have a constant amplitude. However an AM radio may detect the sound of an FM broadcast by the phenomenon of slope detection which occurs when the radio is tuned slightly above or below the nominal broadcast frequency. Frequency variation on one sloping side of the radio tuning curve gives the amplified signal a corresponding local amplitude variation, to which the AM detector is sensitive. Slope detection gives inferior distortion and noise rejection compared to the following dedicated FM detectors that are normally used.

Phase detector

A phase detector is a nonlinear device whose output represents the phase difference between the two oscillating input signals. It has two inputs and one output: a reference signal is applied to one input and the phase or frequency modulated signal is applied to the other. The output is a signal that is proportional to the phase difference between the two inputs.
In phase demodulation the information is contained in the amount and rate of phase shift in the carrier wave.

The Foster-Seeley discriminator

The Foster-Seeley discriminator  is a widely used FM detector. The detector consists of a special center-tapped transformer feeding two diodes in a full wave DC rectifier circuit. When the input transformer is tuned to the signal frequency, the output of the discriminator is zero. When there is no deviation of the carrier, both halves of the center tapped transformer are balanced. As the FM signal swings in frequency above and below the carrier frequency, the balance between the two halves of the center-tapped secondary is destroyed and there is an output voltage proportional to the frequency deviation.

Ratio detector

A ratio detector using solid-state diodes
The ratio detector  is a variant of the Foster-Seeley discriminator, but one diode conducts in an opposite direction, and using a tertiary winding in the preceding transformer. The output in this case is taken between the sum of the diode voltages and the center tap. The output across the diodes is connected to a large value capacitor, which eliminates AM noise in the ratio detector output. The ratio detector has the advantage over the Foster-Seeley discriminator that it will not respond to AM signals, thus potentially saving a limiter stage; however the output is only 50% of the output of a discriminator for the same input signal. The ratio detector has wider bandwidth but more distortion than the Foster-Seeley discriminator.

Quadrature detector

In quadrature detectors, the received FM signal is split into two signals. One of the two signals is then passed through a high-reactance capacitor, which shifts the phase of that signal by 90 degrees. This phase-shifted signal is then applied to an LC circuit, which is resonant at the FM signal's unmodulated, "center," or "carrier" frequency. If the received FM signal's frequency equals the center frequency, then the two signals will have a 90-degree phase difference and they are said to be in "phase quadrature" — hence the name of this method. The two signals are then multiplied together in an analog or digital device, which serves as a phase detector; that is, a device whose output is proportional to the phase difference between two signals. In the case of an unmodulated FM signal, the phase detector's output is — after the output has been filtered; that is, averaged over time — constant; namely, zero. However, if the received FM signal has been modulated, then its frequency will vary from the center frequency. In this case, the resonant LC circuit will further shift the phase of the signal from the capacitor, so that the signal's total phase shift will be the sum of the 90 degrees that's imposed by the capacitor and the positive or negative phase change that's imposed by the LC circuit. Now the output from the phase detector will differ from zero, and in this way, one recovers the original signal that was used to modulate the FM carrier.
This detection process can also be accomplished by combining, in an exclusive-OR (XOR) logic gate, the original FM signal and a square wave whose frequency equals the FM signal's center frequency. The XOR gate produces an output pulse whose duration equals the difference between the times at which the square wave and the received FM signal pass through zero volts. As the FM signal's frequency varies from its unmodulated center frequency (which is also the frequency of the square wave), the output pulses from the XOR gate become longer or shorter. (In essence, this quadrature detector converts an FM signal into a pulse-width modulated (PWM) signal.) When these pulses are filtered, the filter's output rises as the pulses grow longer and its output falls as the pulses grow shorter. In this way, one recovers the original signal that was used to modulate the FM carrier.

Other FM detectors

Less common, specialized, or obsolescent types of detectors include:
  • Travis or double tuned circuit discriminator using two non-interacting tuned circuits above and below the nominal center frequency
  • Weiss discriminator which uses a single LC tuned circuit or crystal
  • Pulse count discriminator which converts the frequency to a train of constant amplitude pulses, producing a voltage directly proportional to the frequency.

Phase-locked loop detector

The phase-locked loop detector requires no frequency-selective LC network to accomplish demodulation. In this system, a voltage controlled oscillator (VCO) is phase locked by a feedback loop, which forces the VCO to follow the frequency variations of the incoming FM signal. The low-frequency error voltage that forces the VCO's frequency to track the frequency of the modulated FM signal is the demodulated audio output. 



                                                                          X  .  II
                                                  CRYSTAL RADIO AND  DETEKTOR

A crystal radio receiver, also called a crystal set or cat's whisker receiver, is a very simple radio receiver, popular in the early days of radio. It needs no other power source but that received solely from the power of radio waves received by a wire antenna. It gets its name from its most important component, known as a crystal detector, originally made from a piece of crystalline mineral such as galena. This component is now called a diode.
Crystal radios are the simplest type of radio receiver an Tutup d can be made with a few inexpensive parts, such as a wire for an antenna, a coil of copper wire for adjustment, a capacitor, a crystal detector, and earphones. Crystal radios are distinct from ordinary radios as they are passive receivers, while other radios use a separate source of electric power such as a battery or the mains power to amplify the weak radio signal so as to make it louder. Thus, crystal sets produce rather weak sound and must be listened to with sensitive earphones, and can only receive stations within a limited range.
Today they are still sold as educational devices, and there are groups of enthusiasts devoted to their construction . Crystal radios receive amplitude modulated (AM) signals, and can be designed to receive almost any radio frequency band, but most receive the AM broadcast band. A few receive shortwave bands, but strong signals are required. The first crystal sets received wireless telegraphy signals broadcast by spark-gap transmitters at frequencies as low as 20 kHz.   

   1970s-era crystal radio marketed to children. The earphone is on left. The antenna wire, right, has a clip to attach to metal objects such as a bedspring, which serve as an additional antenna to improve reception.

Bright clouds

A family listening to a crystal radio in the 1920s
Greenleaf Whittier Pickard's US Patent 836,531 "Means for receiving intelligence communicated by electric waves" diagram
Radio receiver, Basel, Switzerland, 1914
NBS Circular 120 Home Crystal Radio Project
Crystal radio used as a backup receiver on a World War II Liberty ship  


Crystal radio was invented by a long, partly obscure chain of discoveries in the late 19th century that gradually evolved into more and more practical radio receivers in the early 20th century. The earliest practical use of crystal radio was to receive Morse code radio signals transmitted, from spark-gap transmitters, by early amateur radio experimenters. As electronics evolved, the ability to send voice signals by radio caused a technological explosion in the years around 1920 that evolved into today's radio broadcasting industry.

Early years

Early radio telegraphy used spark gap and arc transmitters as well as high-frequency alternators running at radio frequencies. The coherer was the first means of detecting a radio signal. These, however, lacked the sensitivity to detect weak signals.
In the early 20th century, various researchers discovered that certain metallic minerals, such as galena, could be used to detect radio signals.
Pickard's detector was revolutionary in that he found that a fine pointed wire known as a "cat's whisker", in delicate contact with a mineral, produced the best semiconductor effect (that of rectification).
A crystal detector includes a crystal, a special thin wire that contacts the crystal, and the stand that holds those components in place. The most common crystal used is a small piece of galena; pyrite was also often used, as it was a more easily adjusted and stable mineral, and quite sufficient for urban signal strengths. Several other minerals also performed well as detectors. Another benefit of crystals was that they could demodulate amplitude modulated signals. This device brought radiotelephones and voice broadcast to a public audience. Crystal sets represented an inexpensive and technologically simple method of receiving these signals at a time when the embryonic radio broadcasting industry was beginning to grow.

Crystodyne
crystodyne applying voltage biases to various kinds of crystals for manufacture of radio detectors. The result was astonishing: with a zincite (zinc oxide) crystal he gained amplification. This was negative resistance phenomenon, decades before the development of the tunnel diode. After the first experiments, Losev built regenerative and superheterodyne receivers, and even transmitters.
A crystodyne could be produced in primitive conditions; it can be made in a rural forge, unlike vacuum tubes and modern semiconductor devices. However, this discovery was not supported by authorities and soon forgotten; no device was produced in mass quantity beyond a few examples for research.

"Foxhole radios"

"Foxhole radio" used on the Italian Front in World War 2. It uses a pencil lead attached to a safety pin pressing against a razor blade for a detector.
 
 
In addition to mineral crystals, the oxide coatings of many metal surfaces act as semiconductors (detectors) capable of rectification. Crystal radios have been improvised using detectors made from rusty nails, corroded pennies, and many other common objects.


Design

 
 
Block diagram of a crystal radio receiver
A crystal radio can be thought of as a radio receiver reduced to its essentials. It consists of at least these components:
  • An antenna in which electric currents are induced by the radio waves.
  • A resonant circuit (tuned circuit) which serves to select the frequency of the desired radio station out of all the radio signals received by the antenna. The tuned circuit consists of a coil of wire (called an inductor) and a capacitor connected together, so as to create a circuit that resonates at the frequency of the desired station, and hence "tune" in that station. One or both of the coil or capacitor is adjustable, allowing the circuit to be tuned to different frequencies. In some circuits a capacitor is not used, as the antenna also serves as the capacitor. The tuned circuit has a resonant frequency and allows radio waves at that frequency to pass to the detector, while rejecting waves at all other frequencies. Such a circuit is also known as a bandpass filter.
  • A semiconductor crystal (detector) that demodulates the radio signal to get the audio signal (modulation). The crystal detector is a nonlinear impedance that functions as a square law detector[citation needed]. The detector's output is converted to sound by the earphone. Early sets used a cat's whisker detector, consisting of a fine wire touching the surface of a sample of crystalline mineral such as galena. It was this component that gave crystal sets their name.
  • An earphone to convert the audio signal to sound waves so they can be heard. The low power produced by a crystal receiver is insufficient to power a loudspeaker, hence earphones are used. 
 
 
Pictorial diagram from 1922 showing the circuit of a crystal radio. This common circuit did not use a tuning capacitor, but used the capacitance of the antenna to form the tuned circuit with the coil. The detector might have been a piece of galena with a whisker wire in contact with it on a part of the crystal, making a diode contact 

As a crystal radio has no power supply, the sound power produced by the earphone comes solely from the transmitter of the radio station being received, via the radio waves captured by the antenna. The power available to a receiving antenna decreases with the square of its distance from the radio transmitter. Even for a powerful commercial broadcasting station, if it is more than a few miles from the receiver the power received by the antenna is very small, typically measured in microwatts or nanowatts. In modern crystal sets, signals as weak as 50 picowatts at the antenna can be heard. Crystal radios can receive such weak signals without using amplification only due to the great sensitivity of human hearing, which can detect sounds with an intensity of only 10−16 W/cm2. Therefore, crystal receivers have to be designed to convert the energy from the radio waves into sound waves as efficiently as possible. Even so, they are usually only able to receive stations within distances of about 25 miles for AM broadcast stations, although the radiotelegraphy signals used during the wireless telegraphy era could be received at hundreds of miles, and crystal receivers were even used for transoceanic communication during that period.
Commercial passive receiver development was abandoned with the advent of reliable vacuum tubes around 1920, and subsequent crystal radio research was primarily done by radio amateurs and hobbyists. Many different circuits have been used. The following sections discuss the parts of a crystal radio in greater detail.

Antenna

The antenna converts the energy in the electromagnetic radio waves to an alternating electric current in the antenna, which is connected to the tuning coil. Since in a crystal radio all the power comes from the antenna, it is important that the antenna collect as much power from the radio wave as possible. The larger an antenna, the more power it can intercept. Antennas of the type commonly used with crystal sets are most effective when their length is close to a multiple of a quarter-wavelength of the radio waves they are receiving. Since the length of the waves used with crystal radios is very long (AM broadcast band waves are 182-566 m or 597–1857 ft. long) the antenna is made as long as possible, from a long wire, in contrast to the whip antennas or ferrite loopstick antennas used in modern radios.
Serious crystal radio hobbyists use "inverted L" and "T" type antennas, consisting of hundreds of feet of wire suspended as high as possible between buildings or trees, with a feed wire attached in the center or at one end leading down to the receiver. However more often random lengths of wire dangling out windows are used. A popular practice in early days (particularly among apartment dwellers) was to use existing large metal objects, such as bedsprings,  fire escapes, and barbed wire fences as antennas.

Ground

The wire antennas used with crystal receivers are monopole antennas which develop their output voltage with respect to ground. The receiver thus requires a connection to ground (the earth) as a return circuit for the current. The ground wire was attached to a radiator, water pipe, or a metal stake driven into the ground. In early days if an adequate ground connection could not be made a counterpoise was sometimes used. A good ground is more important for crystal sets than it is for powered receivers, as crystal sets are designed to have a low input impedance needed to transfer power efficiently from the antenna. A low resistance ground connection (preferably below 25 Ω) is necessary because any resistance in the ground reduces available power from the antenna. In contrast, modern receivers are voltage-driven devices, with high input impedance, hence little current flows in the antenna/ground circuit. Also, mains powered receivers are grounded adequately through their power cords, which are in turn attached to the earth by way of a well established ground.

Tuned circuit

The earliest crystal receiver circuit did not have a tuned circuit 


The tuned circuit, consisting of a coil and a capacitor connected together, acts as a resonator, similar to a tuning fork. Electric charge, induced in the antenna by the radio waves, flows rapidly back and forth between the plates of the capacitor through the coil. The circuit has a high impedance at the desired radio signal's frequency, but a low impedance at all other frequencies. Hence, signals at undesired frequencies pass through the tuned circuit to ground, while the desired frequency is instead passed on to the detector (diode) and stimulates the earpiece and is heard. The frequency of the station received is the resonant frequency f of the tuned circuit, determined by the capacitance C of the capacitor and the inductance L of the coil:
f={\frac {1}{2\pi {\sqrt {LC}}}}\,
By varying either the inductor (L) or the capacitance (C), the circuit can be adjusted to different frequencies. In inexpensive sets, the inductor was made variable via a spring contact pressing against the windings that could slide along the coil, thereby introducing a larger or smaller number of turns of the coil into the circuit. Thus the inductance could be varied, "tuning" the circuit to the frequencies of different radio stations.Alternatively, a variable capacitor is used to tune the circuit. Some modern crystal sets use a ferrite core tuning coil, in which a ferrite magnetic core is moved into and out of the coil, thereby varying the inductance by changing the magnetic permeability (this eliminated the less reliable mechanical contact).
The antenna is an integral part of the tuned circuit and its reactance contributes to determining the circuit's resonant frequency. Antennas usually act as a capacitance, as antennas shorter than a quarter-wavelength have capacitive reactance. Many early crystal sets did not have a tuning capacitor, and relied instead on the capacitance inherent in the wire antenna (in addition to significant parasitic capacitance in the coil) to form the tuned circuit with the coil.
The earliest crystal receivers did not have a tuned circuit at all, and just consisted of a crystal detector connected between the antenna and ground, with an earphone across it. Since this circuit lacked any frequency-selective elements besides the broad resonance of the antenna, it had little ability to reject unwanted stations, so all stations within a wide band of frequencies were heard in the earphone (in practice the most powerful usually drowns out the others). It was used in the earliest days of radio, when only one or two stations were within a crystal set's limited range.

Impedance matching



"Two            slider" crystal radio circuit. and example from 1920s. The two sliding contacts on the coil allowed the impedance of the radio to be adjusted to match the antenna as theradio was tuned, resulting in stronger reception
An important principle used in crystal radio design to transfer maximum power to the earphone is impedance matching. The maximum power is transferred from one part of a circuit to another when the impedance of one circuit is the complex conjugate of that of the other; this implies that the two circuits should have equal resistance. However, in crystal sets, the impedance of the antenna-ground system (around 10-200 ohms ) is usually lower than the impedance of the receiver's tuned circuit (thousands of ohms at resonance), and also varies depending on the quality of the ground attachment, length of the antenna, and the frequency to which the receiver is tuned.
Therefore, in improved receiver circuits, in order to match the antenna impedance to the receiver's impedance, the antenna was connected across only a portion of the tuning coil's turns. This made the tuning coil act as an impedance matching transformer (in an autotransformer connection) in addition to providing the tuning function. The antenna's low resistance was increased (transformed) by a factor equal to the square of the turns ratio (the ratio of the number of turns the antenna was connected to, to the total number of turns of the coil), to match the resistance across the tuned circuit. In the "two-slider" circuit, popular during the wireless era, both the antenna and the detector circuit were attached to the coil with sliding contacts, allowing (interactive) adjustment of both the resonant frequency and the turns ratio. Alternatively a multiposition switch was used to select taps on the coil. These controls were adjusted until the station sounded loudest in the earphone.

Problem of selectivity

Direct-coupled circuit with impedance matching
One of the drawbacks of crystal sets is that they are vulnerable to interference from stations near in frequency to the desired station; that is to say, they have low selectivity. Often two or more stations are heard simultaneously. This is because the simple tuned circuit does not reject nearby signals well; it allows a wide band of frequencies to pass through, that is, it has a large bandwidth (low Q factor) compared to modern receivers.
The crystal detector worsened the problem, because it has relatively low resistance, thus it "loaded" the tuned circuit, damping the oscillations (lowering the response), and reducing its Q. In many circuits, the selectivity was improved by connecting the detector and earphone circuit to a tap across only a fraction of the coil's turns. This reduced the impedance loading of the tuned circuit, as well as improving the impedance match with the detector.

Inductive coupling

Inductively-coupled circuit with impedance matching. This type was used in most quality crystal receivers
Amateur-built crystal receiver with "loose coupler" antenna transformer, Belfast, around 1914
In more sophisticated crystal receivers, the tuning coil is replaced with an adjustable air core antenna coupling transformer which improves the selectivity by a technique called loose coupling.  This consists of two magnetically coupled coils of wire, one (the primary) attached to the antenna and ground and the other (the secondary) attached to the rest of the circuit. The current from the antenna creates an alternating magnetic field in the primary coil, which induced a current in the secondary coil which was then rectified and powered the earphone. Each of the coils functions as a tuned circuit; the primary coil resonated with the capacitance of the antenna (or sometimes another capacitor), and the secondary coil resonated with the tuning capacitor. Both the primary and secondary were tuned to the frequency of the station. The two circuits interacted to form a resonant transformer.
Reducing the coupling between the coils, by physically separating them so that less of the magnetic field of one intersects the other, reduces the mutual inductance, narrows the bandwidth, and results in much sharper, more selective tuning than that produced by a single tuned circuit. However, the looser coupling also reduced the power of the signal passed to the second circuit. The transformer was made with adjustable coupling, to allow the listener to experiment with various settings to gain the best reception.
One design common in early days, called a "loose coupler", consisted of a smaller secondary coil inside a larger primary coil The smaller coil was mounted on a rack so it could be slid linearly in or out of the larger coil. If radio interference was encountered, the smaller coil would be slid further out of the larger, loosening the coupling, narrowing the bandwidth, and thereby rejecting the interfering signal.
The antenna coupling transformer also functioned as an impedance matching transformer, that allowed a better match of the antenna impedance to the rest of the circuit. One or both of the coils usually had several taps which could be selected with a switch, allowing adjustment of the number of turns of that transformer and hence the "turns ratio".
Coupling transformers were difficult to adjust, because the three adjustments, the tuning of the primary circuit, the tuning of the secondary circuit, and the coupling of the coils, were all interactive, and changing one affected the others.

Crystal detector

Galena cat's whisker detector
Germanium diode used in modern crystal radios (about 3 mm long)
How the crystal detector works. (A) The amplitude modulated radio signal from the tuned circuit. The rapid oscillations are the radio frequency carrier wave. The audio signal (the sound) is contained in the slow variations (modulation) of the amplitude (hence the term amplitude modulation, AM) of the waves. This signal cannot be converted to sound by the earphone, because the audio excursions are the same on both sides of the axis, averaging out to zero, which would result in no net motion of the earphone's diaphragm. (B) The crystal conducts current better in one direction than the other, producing a signal whose amplitude does not average to zero but varies with the audio signal. (C) A bypass capacitor is used to remove the radio frequency carrier pulses, leaving the audio signal
Circuit with detector bias battery to improve sensitivity and buzzer to adjust cat's whisker
The crystal detector demodulates the radio frequency signal, extracting the modulation (the audio signal which represents the sound waves) from the radio frequency carrier wave. In early receivers, the detector was a cat's whisker detector consisting of a fine metal wire, the "cat's whisker", on an adjustable arm that touched a pea-sized lump of semiconducting mineral. The point of contact between the wire and the crystal produced a diode effect. The cat's whisker detector was a crude Schottky diode that allowed current to flow better in one direction than in the opposite direction. Modern crystal sets use modern semiconductor diodes. The crystal functions as an envelope detector, rectifying the alternating current radio signal to a pulsing direct current, the peaks of which trace out the audio signal, so it can be converted to sound by the earphone, which is connected to the detector. The rectified current from the detector has radio frequency pulses from the carrier frequency in it, which are blocked by the high inductive reactance and do not pass well through the coils of early date earphones. Hence, a small capacitor called a bypass capacitor is often placed across the earphone terminals; its low reactance at radio frequency bypasses these pulses around the earphone to ground. In some sets the earphone cord had enough capacitance that this component could be omitted.
In a cat's whisker detector only certain sites on the crystal surface functioned as rectifying junctions, and the device was very sensitive to the pressure of the crystal-wire contact, which could be disrupted by the slightest vibration. Therefore, a usable contact point had to be found by trial and error before each use. The operator dragged the wire across the crystal surface until a radio station or "static" sounds were heard in the earphones. Alternatively, some radios (circuit, right) used a battery-powered buzzer attached to the input circuit to adjust the detector. The spark at the buzzer's electrical contacts served as a weak source of static, so when the detector began working, the buzzing could be heard in the earphones. The buzzer was then turned off, and the radio tuned to the desired station.
Galena (lead sulfide) was probably the most common crystal used in cat's whisker detectors, but various other types of crystals were also used, the most common being iron pyrite (fool's gold, FeS2), silicon, molybdenite (MoS2), silicon carbide (carborundum, SiC), and a zincite-bornite (ZnO-Cu5FeS4) crystal-to-crystal junction trade-named Perikon. Crystal radios have also been improvised from a variety of common objects, such as blue steel razor blades and lead pencils, rusty needles, and pennies In these, a semiconducting layer of oxide or sulfide on the metal surface is usually responsible for the rectifying action.
In modern sets, a semiconductor diode is used for the detector, which is much more reliable than a cat's whisker detector and requires no adjustments. Germanium diodes (or sometimes Schottky diodes) are used instead of silicon diodes, because their lower forward voltage drop (roughly 0.3V compared to 0.6V makes them more sensitive.
All semiconductor detectors function rather inefficiently in crystal receivers, because the low voltage input to the detector is too low to result in much difference between forward better conduction direction, and the reverse weaker conduction. To improve the sensitivity of some of the early crystal detectors, such as silicon carbide, a small forward bias voltage was applied across the detector by a battery and potentiometer. The bias moves the diode's operating point higher on the detection curve producing more signal voltage at the expense of less signal current (higher impedance). There is a limit to the benefit that this produces, depending on the other impedances of the radio. This improved sensitivity was caused by moving the DC operating point to a more desirable voltage-current operating point (impedance) on the junction's I-V curve. The battery did not power the radio, but only provided the biasing voltage which required little power.

Earphones

 
 
Modern crystal radio with piezoelectric earphone 

The requirements for earphones used in crystal sets are different from earphones used with modern audio equipment. They have to be efficient at converting the electrical signal energy to sound waves, while most modern earphones sacrifice efficiency in order to gain high fidelity reproduction of the sound. In early homebuilt sets, the earphones were the most costly component.
The early earphones used with wireless-era crystal sets had moving iron drivers that worked in a way similar to the horn loudspeakers of the period; modern loudspeakers use a moving-coil principle. Each earpiece contained a permanent magnet about which was a coil of wire which formed a second electromagnet. Both magnetic poles were close to a steel diaphram of the speaker. When the audio signal from the radio was passed through the electromagnet's windings, current was caused to flow in the coil which created a varying magnetic field that augmented or diminished that due to the permanent magnet. This varied the force of attraction on the diaphragm, causing it to vibrate. The vibrations of the diaphragm push and pull on the air in front of it, creating sound waves. Standard headphones used in telephone work had a low impedance, often 75 Ω, and required more current than a crystal radio could supply. Therefore, the type used with crystal set radios (and other sensitive equipment) was wound with more turns of finer wire giving it a high impedance of 2000-8000 Ω.
Modern crystal sets use piezoelectric crystal earpieces, which are much more sensitive and also smaller. They consist of a piezoelectric crystal with electrodes attached to each side, glued to a light diaphragm. When the audio signal from the radio set is applied to the electrodes, it causes the crystal to vibrate, vibrating the diaphragm. Crystal earphones are designed as ear buds that plug directly into the ear canal of the wearer, coupling the sound more efficiently to the eardrum. Their resistance is much higher (typically megohms) so they do not greatly "load" the tuned circuit, allowing increased selectivity of the receiver. The piezoelectric earphone's higher resistance, in parallel with its capacitance of around 9 pF, creates a filter that allows the passage of low frequencies, but blocks the higher frequencies. In that case a bypass capacitor is not needed (although in practice a small one of around 0.68 to 1 nF is often used to help improve quality), but instead a 10-100 kΩ resistor must be added in parallel with the earphone's input.
Although the low power produced by crystal radios is typically insufficient to drive a loudspeaker, some homemade 1960s sets have used one, with an audio transformer to match the low impedance of the speaker to the circuit. Similarly, modern low-impedance (8 Ω) earphones cannot be used unmodified in crystal sets because the receiver does not produce enough current to drive them. They are sometimes used by adding an audio transformer to match their impedance with the higher impedance of the driving antenna circuit.

Use as a power source

A crystal radio tuned to a strong local transmitter can be used as a power source for a second amplified receiver of a distant station that cannot be heard without amplification.
There is a long history of unsuccessful attempts and unverified claims to recover the power in the carrier of the received signal itself. Traditional crystal sets use half-wave rectifiers. As AM signals have a modulation factor of only 30% by voltage at peaks, no more than 9% of received signal power (P=U^{2}/R) is actual audio information, and 91% is just rectified DC voltage. Given that the audio signal is unlikely to be at peak all the time, the ratio of energy is, in practice, even greater. Considerable effort was made to convert this DC voltage into sound energy. Some earlier attempts include a one-transistor amplifier in 1966. Sometimes efforts to recover this power are confused with other efforts to produce a more efficient detection. This history continues now with designs as elaborate as "inverted two-wave switching power unit". 


                                                                                       X  .  IIII  

     

                       Electro-optical sensor  

                       in detector aplication 

                      Hasil gambar untuk electronic signal detector

Electro-optical sensors are electronic detectors that convert light, or a change in light, into an electronic signal. They are used in many industrial and consumer applications, for example:

Function

An optical sensor converts light rays into electronic signals. It measures the physical quantity of light and then translates it into a form that is readable by an instrument. An optical sensor is generally part of a larger system that integrates a source of light, a measuring device and the optical sensor. This is often connected to an electrical trigger. The trigger reacts to a change in the signal within the light sensor. An optical sensor can measure the changes from one or several light beams. When a change occurs, the light sensor operates as a photoelectric trigger and therefore either increases or decreases the electrical output. An optical switch enables signals in optical fibres or integrated optical circuits to be switched selectively from one circuit to another. An optical switch can operate by mechanical means or by electro-optic effects, magneto-optic effects as well as by other methods. Optical switches are optoelectronic devices which can be integrated with integrated or discrete microelectronic circuits.

Types of Optical Sensors and Switches

There are many different kinds of optical sensors, the most common types are:
  • Photoconductive devices convert a change of incident light into a change of resistance.
  • Photovoltaics, commonly known as solar cells, convert an amount of incident light into an output voltage.
  • Photodiodes convert an amount of incident light into an output current.
  • Phototransistors are a type of bipolar transistor where the base-collector junction is exposed to light. This results in the same behaviour of a photodiode, but with an internal gain.
Optical Switches are usually used in optical fibers, where the electro-optic effect is used to switch one circuit to another. These switches can be implemented with, for example, microelectromechanical systems or piezoelectric systems.

Applications

Electro-optical sensors are used whenever light needs to be converted to energy. Because of this, electro-optical sensors can be seen almost anywhere. Common applications are smartphones where sensors are used to adjust screen brightness, and smartwatches in which sensors are used to measure the wearer's heartbeat.
Optical sensors can be found in the energy field to monitor structures that generate, produce, distribute, and convert electrical power. The distributed and nonconductive nature of optical fibres makes optical sensors perfect for oil and gas applications, including pipeline monitoring. They can also be found in wind turbine blade monitoring, offshore platform monitoring, power line monitoring and downhole monitoring. Other applications include the civil and transportation fields such as bridge, airport landing strip, dam, railway, airplane, wing, fuel tank and ship hull monitoring.
Among other applications, optical switches can be found in thermal methods which vary the refraction index in one leg of an interferometer in order to switch the signal, MEMS approaches involving arrays of micromirrors that can deflect an optical signal to the appropriate receiver, piezoelectric beam steering liquid crystals which rotate polarized light depending on the applied electric field and acousto-optic methods which change the refraction index as a result of strain induced by an acoustic field to deflect light.
Another important application of optical sensor is to measure the concentration of different compounds by both visible and infrared spectroscopy.

Light fixture

A large number of light fixtures and lamps at a store. 

Ceiling light fixtures 

A light fixture (US English), light fitting (UK English), or luminaire is an electrical device used to create artificial light by use of an electric lamp. All light fixtures have a fixture body and a light socket to hold the lamp and allow for its replacement. Fixtures may also have a switch to control the light, either attached to the lamp body or attached to the power cable. Permanent light fixtures, such as dining room chandeliers, may use a wall switch to turn them on and off; as such, these fixtures may have no switch on the fixture itself. Fixtures require an electrical connection to a power source, typically AC mains power, but also battery power for camping or emergency lights. Permanent lighting fixtures may be directly wired. Moveable lamps have a plug and cord so that they can be plugged into a wall socket. Light fixtures may also have other features, such as reflectors for directing the light, an aperture (with or without a lens), an outer shell or housing for lamp alignment and protection, an electrical ballast or power supply, and a shade to diffuse the light or direct it towards a workspace (e.g., a desk lamp). A wide variety of special light fixtures are created for use in the automotive lighting industry, aerospace, marine and medicine sectors.
Portable light fixtures are often called "lamps", as in table lamp or desk lamp. In technical terminology, the lamp is the light source, which is typically called the light bulb. The term luminaire is recommended by the International Electrotechnical Commission (IEC) for technical use.

a bright cloud

Industrial light fixture, designed by Peter Behrens, around 1915
Fixture manufacturing began soon after production of the incandescent light bulb. When practical uses of fluorescent lighting were realized after 1924, the three leading companies to produce various fixtures were Lightolier, Artcraft Fluorescent Lighting Corporation, and Globe Lighting in the United States.

Fixture types

Light fixtures are classified by how the fixture is installed, the light function or lamp type.

Free-standing or portable

Tiffany dragonfly desk lamp with pigeon sculptures

Fixed

  • Ceiling Dome — Also called the light source(s) are hidden behind a translucent dome typically made of glass, with some combination of frosting and surface texturing to diffuse the light. These can be flush mount fixtures which are mounted right up against the ceiling, or semi-flush fixtures which are separated by a small distance (usually about 3-12").
    • Open ceiling dome — the translucent dome is suspended a short distance below the ceiling by a mechanism that is hidden with the exception of a screw-knob or other device appearing on the outer dome face, and pulling this knob releases the dome
    • Enclosed ceiling dome The translucent dome mates with a ring that is mounted flush with the ceiling
  • Recessed light — the protective housing is concealed behind a ceiling or wall, leaving only the fixture itself exposed. The ceiling-mounted version is often called a downlight.
    • "Cans" with a variety of lamps — this term is jargon for inexpensive downlighting products that are recessed into the ceiling, or sometimes for uplights placed on the floor. The name comes from the shape of the housing. The term "pot lights" is often used in Canada and parts of the US.
    • Cove light — recessed into the ceiling in a long box against a wall.
    • Troffer — recessed fluorescent light fixtures, usually rectangular in shape to fit into a drop ceiling grid.
A chandelier light fixture
  • Surface-mounted light — the finished housing is exposed, not flush with surface
    • Chandelier
    • Pendant light — suspended from the ceiling with a chain or pipe
    • Sconce — provide up or down lights; can be used to illuminate artwork, architectural details; commonly used in hallways or as an alternative to overhead lighting.
    • Track lighting fixture — individual fixtures ("track heads") can be positioned anywhere along the track, which provides electric power.
    • Under-cabinet light — mounted below kitchen wall cabinets
    • Display Case or Showcase light — shows merchandise on display within an enclosed case such as jewelry, grocery stores, and chain stores.
    • Ceiling fan - May sometimes have a light, often referred to as a light kit mounted to it.
    • Emergency lighting or exit sign — connected to a battery backup or to an electric circuit that has emergency power if the mains power fails
    • High- and low-bay lighting — typically used for general lighting for industrial buildings and often big-box stores
    • Strip lights or Industrial lighting — often long lines of fluorescent lamps used in a warehouse or factory
A decorative outdoor lamp at Leeds Town Hall.
A garden solar lamp is an example of landscape lighting

Special-purpose lights

Lamp types

Old table lamps at Archaeological Museum, Sri Lanka
Xenon arc lamp, Yablochkov candle
Fluorescent lamp, compact fluorescent lamp (CFL), Induction lamp, blacklight.
  • Fuel lamps
Betty lamp, butter lamp, carbide lamp, gas lighting, kerosene lamp, oil lamp, rush light, torch, candle, Limelight, gas mantle
Safety lamps: Davy lamp & Geordie lamp
Mercury-vapor lamp, Metal-halide (HMI, HQI, CDM), Sodium vapor or "high-pressure sodium"
A-lamp, Parabolic aluminized reflector lamp (PAR), reflector lamp (R), bulged reflector lamp (BR) (refer to lamp shapes)
Table Lighting

Light-fixture controls


Position sensor  :   


A position sensor is any device that permits position measurement. It can either be an absolute position sensor or a relative one (displacement sensor). Position sensors can be linear, angular, or multi-axis.
Some position sensors available today:


Flash (photography)



The high-speed wing action of a hummingbird hawk-moth is frozen by flash. The flash has given the foreground more illumination than the background. See Inverse-square law

Video demonstration of high speed flash photography. 

A flash is a device used in photography producing a flash of artificial light (typically 1/1000 to 1/200 of a second) at a color temperature of about 5500 K (Kelvin)[citation needed] to help illuminate a scene. A major purpose of a flash is to illuminate a dark scene. Other uses are capturing quickly moving objects or changing the quality of light. Flash refers either to the flash of light itself or to the electronic flash unit discharging the light. Most current flash units are electronic, having evolved from single-use flashbulbs and flammable powders. Modern cameras often activate flash units automatically.
Flash units are commonly built directly into a camera. Some cameras allow separate flash units to be mounted via a standardized "accessory mount" bracket (a hot shoe). In professional studio equipment, flashes may be large, standalone units, or studio strobes, powered by special battery packs or connected to mains power. They are either synchronized with the camera using a flash synchronization cable or radio signal, or are light-triggered, meaning that only one flash unit needs to be synchronized with the camera, and in turn triggers the other units, called slaves.

Types of flash

Flash-lamp

Demonstration of a magnesium flash powder lamp from 1909 

Studies of magnesium by Bunsen and Roscoe in 1859 showed that burning this metal produced a light with similar qualities to daylight. The potential application to photography inspired Edward Sonstadt to investigate methods of manufacturing magnesium so that it would burn reliably for this use. He applied for patents in 1862 and by 1864 had started the Manchester Magnesium Company with Edward Mellor. With the help of engineer William Mather, who was also a director of the company, they produced flat magnesium ribbon, which was said to burn more consistently and completely so giving better illumination than round wire. It also had the benefit of being a simpler and cheaper process than making round wire.[1] Mather was also credited with the invention of a holder for the ribbon, which formed a lamp to burn it in.[2] A variety of magnesium ribbon holders were produced by other manufacturers, such as the Pistol Flashmeter, which incorporated an inscribed ruler that allowed the photographer to use the correct length of ribbon for the exposure they needed. The packaging also implies that the magnesium ribbon was not necessarily broken off before being ignited.

Vintage AHA smokeless flash powder lamp kit, Germany 

An alternative to ribbon was flash powder, a mixture of magnesium powder and potassium chlorate, introduced by its German inventors Adolf Miethe and Johannes Gaedicke in 1887. A measured amount was put into a pan or trough and ignited by hand, producing a brief brilliant flash of light, along with the smoke and noise that might be expected from such an explosive event. This could be a life-threatening activity, especially if the flash powder was damp. An electrically triggered flash lamp was invented by Joshua Lionel Cowen in 1899. His patent describes a device for igniting photographers’ flash powder by using dry cell batteries to heat a wire fuse. Variations and alternatives were touted from time to time and a few found a measure of success in the marketplace, especially for amateur use. In 1905, one French photographer was using intense non-explosive flashes produced by a special mechanized carbon arc lamp to photograph subjects in his studio, but more portable and less expensive devices prevailed. On through the 1920s, flash photography normally meant a professional photographer sprinkling powder into the trough of a T-shaped flash lamp, holding it aloft, then triggering a brief and (usually) harmless bit of pyrotechnics.

Flashbulbs

Ernst Leitz Wetzlar flash from 1950s
 
Flashbulbs have ranged in size from the diminutive AG-1 to the massive No. 75.
Kodak Brownie Hawkeye with "Kodalite Flasholder" and Sylvania P25 blue-dot daylight-type flashbulb
The AG-1 flashbulb, introduced in 1958, used wires protruding from its base as electrical contacts; this eliminated the need for a separate metal base.  



Flashcubes, Magicubes and Flipflash
Flashcube fitted to a Kodak Instamatic camera, showing both unused (left) and used (right) bulbs 

Undersides of Flashcube (left) and Magicube (right) cartridges 

"Flip flash" type cartridge 


Electronic flash

Electronic flash was developed in the late 1950s while flashbulbs were still in general use. Early units were expensive and often large and heavy as the power unit was a separate unit to the flash gun head and was powered by a large lead-acid battery, and usually carried by the photographer by means of a shoulder strap. Towards the end of the 1960s, the size had dropped to the point where they were matching the size of conventional bulb flash guns (though the price, having dropped, was still an obstacle). The electronic flash system eventually superseded bulb guns as prices came down, rendering flashbulbs virtually obsolete.
A typical electronic flash unit has electronic circuitry to charge a high-capacity capacitor to several hundred volts. When the flash is triggered by the shutter's flash synchronization contact, the capacitor is discharged almost instantaneously through a flash tube, producing a flash of very brief duration almost instantaneously (i.e., the flash duration, often around 1/1000 of a second, is shorter than most practical shutter speeds, and full brightness is reached before the shutter has time to close appreciably). Synchronization of full flash brightness with maximum shutter opening was problematic with bulbs which took an appreciable time to ignite and reach full brightness; electronic flash does not have these difficulties.
Simple electronic flash units are often mounted on or near the camera; many inexpensive cameras have an electronic flash unit built in.

Two professional xenon tube flashes
Some lenses have built-in (ring-)flash lights for shadow free macro photography, but there are also accessory ring flashes available.
In a photographic studio, more powerful and flexible studio flash systems are used. They usually contain a modeling light, an incandescent light bulb close to the flash tube; the continuous illumination of the modeling light lets the photographer visualize the effect of the flash. A system may comprise multiple synchronised flashes for multi-source lighting.
The strength of a flash device is often indicated in terms of a guide number designed to simplify exposure setting. The energy released by larger studio flash units, such as monolights, is indicated in watt-seconds.
The Nikon brand name for its electronic flash units, Speedlight, is frequently used as a generic term for electronic flash equipment.

High speed flash

An air-gap flash is a high-voltage device that discharges a flash of light with an exceptionally short duration, often much less than one microsecond. These are commonly used by scientists or engineers for examining extremely fast-moving objects or reactions, famous for producing images of bullets tearing through light bulbs and balloons (see Harold Eugene Edgerton). An example of a process by which to create a high speed flash is the exploding wire method.

A photo of a Smith & Wesson Model 686 firing, taken with a high speed air-gap flash. The photo was taken in a darkened room, with camera's shutter open and the flash was triggered by the sound of the shot using a microphone.

Multi-flash

A camera that implements multiple flashes can be used to find depth edges or create stylized images. Such a camera has been developed by researchers at the Mitsubishi Electric Research Laboratories (MERL). Successive flashing of strategically placed flash mechanisms results in shadows along the depths of the scene. This information can be manipulated to suppress or enhance details or capture the intricate geometric features of a scene (even those hidden from the eye), to create a non-photorealistic image form. Such images could be useful in technical or medical imaging.

Flash intensity

Unlike flashbulbs, the intensity of an electronic flash can be adjusted on some units. To do this, smaller flash units typically vary the capacitor discharge time, whereas larger (e.g., higher power, studio) units typically vary the capacitor charge. Color temperature can change as a result of varying the capacitor charge, thus making color corrections necessary. Due to advances in semiconductor technology, some studio units can now control intensity by varying the discharge time and thereby provide consistent color temperature.
Flash intensity is typically measured in stops or in fractions (1, 1/2, 1/4, 1/8 etc.). Some monolights display an "EV Number", so that a photographer can know the difference in brightness between different flash units with different watt-second ratings. EV10.0 is defined as 6400 watt-seconds, and EV9.0 is one stop lower, i.e. 3200 watt-seconds.

Flash duration

Flash duration is commonly described by two numbers that are expressed in fractions of a second:
  • t.1 is the length of time the light intensity is above 0.1 (10%) of the peak intensity
  • t.5 is the length of time the light intensity is above 0.5 (50%) of the peak intensity
For example, a single flash event might have a t.5 value of 1/1200 and t.1 of 1/450. These values determine the ability of a flash to "freeze" moving subjects in applications such as sports photography.
In cases where intensity is controlled by capacitor discharge time, t.5 and t.1 decrease with decreasing intensity. Conversely, in cases where intensity is controlled by capacitor charge, t.5 and t.1 increase with decreasing intensity due to the non-linearity of the capacitor's discharge curve.

Flash LED used in phones

High-current flash LEDs are used as flash sources in camera phones, although they are not yet at the power levels to equal xenon flash devices (that are rarely used in phones) in still cameras. The major advantages of LEDs over xenon include low voltage operation, higher efficiency, and extreme miniaturization. The LED flash can also be used for illumination of video recordings or as an autofocus assist lamp in low-light conditions.

Focal-plane-shutter synchronization

Electronic flash units have compatibility issues with focal-plane shutters. Focal-plane shutters expose using two curtains that cross the sensor. The first one opens and the second curtain follows it after a delay equal to the nominal shutter speed. A typical modern focal-plane shutter takes about 1/200 s to cross the sensor, so at exposure times shorter than this only part of the sensor is uncovered at any one time. Electronic flash can have durations as short as 50 µs, so at such short exposure times only part of the sensor is exposed. This limits the shutter speed to about 1/200 s when using flash. In the past, slow-burning single-use flash bulbs allowed the use of focal-plane shutters at maximum speed because they produced continuous light for the time taken for the exposing slit to cross the film gate. If these are found they cannot be used on modern cameras because the bulb must be fired *before* the first shutter curtain begins to move (M-sync); the X-sync used for electronic flash normally fires only when the first shutter curtain reaches the end of its travel.
High-end flash units address this problem by offering a mode, typically called FP sync or HSS (High Speed Sync), which fires the flash tube multiple times during the time the slit traverses the sensor. Such units require communication with the camera and are thus dedicated to a particular camera make. The multiple flashes result in a significant decrease in guide number, since each is only a part of the total flash power, but it's all that illuminates any particular part of the sensor. In general, if s is the shutter speed, and t is the shutter traverse time, the guide number reduces by s / t. For example, if the guide number is 100, and the shutter traverse time is 5 ms (a shutter speed of 1/200s), and the shutter speed is set to 1/2000 s (0.5 ms), the guide number reduces by a factor of 0.5 / 5, or about 3.16, so the resultant guide number at this speed would be about 32.
Current (2010) flash units frequently have much lower guide numbers in HSS mode than in normal modes, even at speeds below the shutter traverse time. For example, the Mecablitz 58 AF-1 digital flash unit has a guide number of 58 in normal operation, but only 20 in HSS mode, even at low speeds.

Technique

Image exposed without additional lighting (left) and with fill flash (right)
Lighting produced by direct flash (left) and bounced flash (right)
As well as dedicated studio use, flash may be used as the main light source where ambient light is inadequate, or as a supplementary source in more complex lighting situations. Basic flash lighting produces a hard, frontal light unless modified in some way. Several techniques are used to soften light from the flash or provide other effects.
  • Softboxes, diffusers that cover the flash lamp, scatter direct light and reduce its harshness.
  • Reflectors, including umbrellas, flat-white backgrounds, drapes and reflector cards are commonly used for this purpose (even with small hand-held flash units).
  • Bounce flash is a related technique in which flash is directed onto a reflective surface, for example a white ceiling or a flash umbrella, which then reflects light onto the subject. It can be used as fill-flash or, if used indoors, as ambient lighting for the whole scene. Bouncing creates softer, less artificial-looking illumination than direct flash, often reducing overall contrast and expanding shadow and highlight detail, and typically requires more flash power than direct lighting. Part of the bounced light can be also aimed directly on the subject by "bounce cards" attached to the flash unit which increase the efficiency of the flash and illuminate shadows cast by light coming from the ceiling. It's also possible to use one's own palm for that purpose, resulting in warmer tones on the picture, as well as eliminating the need to carry additional accessories.
  • Fill flash or "fill-in flash" describes flash used to supplement ambient light in order to illuminate a subject close to the camera that would otherwise be in shade relative to the rest of the scene. The flash unit is set to expose the subject correctly at a given aperture, while shutter speed is calculated to correctly expose for the background or ambient light at that aperture setting. Secondary or slave flash units may be synchronized to the master unit to provide light from additional directions. The slave units are electrically triggered by the light from the master flash. Many small flashes and studio monolights have optical slaves built in. Wireless radio transmitters, such as PocketWizards, allow the receiver unit to be around a corner, or at a distance too far to trigger using an optical sync.
  • Strobe: Some high end units can be set to flash a specified number of times at a specified frequency. This allows action to be frozen multiple times in a single exposure.
  • Colored gels can also be used to change the color of the flash. Correction gels are commonly used, so that the light of the flash is the same as tungsten lights (using a CTO gel) or fluorescent lights.
  • Open flash, Free flash or manually-triggred flash refers to modes in which the photographer manually triggers the flash unit to fire independently of the shutter.

Drawbacks

The distance limitation as seen when taking picture of the wooden floor
Flash
The same picture taken with incandescent ambient light, using a longer exposure and a higher ISO speed setting. The distance is no longer restricted, but the colors are unnatural because of a lack of color temperature compensation, and the picture may suffer from more grain or noise.
No flash
Left: the distance limitation as seen when taking picture of the wooden floor. Right: the same picture taken with incandescent ambient light, using a longer exposure and a higher ISO speed setting. The distance is no longer restricted, but the colors are unnatural because of a lack of color temperature compensation, and the picture may suffer from more grain or noise.
Using a flash in a museum is mostly prohibited.
  • Using on-camera flash will give a very harsh light, which results in a loss of shadows in the image, because the only lightsource is in practically the same place as the camera. Balancing the flash power and ambient lighting or using off-camera flash can help overcome these issues. Using an umbrella or softbox (the flash will have to be off-camera for this) makes softer shadows.
  • A typical problem with cameras using built-in flash units is the low intensity of the flash; the level of light produced will often not suffice for good pictures at distances of over 3 metres (10 ft) or so. Dark, murky pictures with excessive image noise or "grain" will result. In order to get good flash pictures with simple cameras, it is important not to exceed the recommended distance for flash pictures. Larger flashes, especially studio units and monoblocks, have sufficient power for larger distances, even through an umbrella, and can even be used against sunlight at short distances.
  • The "red-eye effect" is another problem with on camera and ring flash units. Since the retina of the human eye reflects red light straight back in the direction it came from, pictures taken from straight in front of a face often exhibit this effect. It can be somewhat reduced by using the "red eye reduction" found on many cameras (a pre-flash that makes the subject's irises contract). However, very good results can be obtained only with a flash unit that is separated from the camera, sufficiently far from the optical axis, or by using bounce flash, where the flash head is angled to bounce light off a wall, ceiling or reflector.
  • On some cameras the flash exposure measuring logic fires a pre-flash very quickly before the real flash. In some camera/people combinations this will lead to shut eyes in every picture taken. The blink response time seems to be around 1/10 of a second. If the exposure flash is fired at approximately this interval after the TTL measuring flash, people will be squinting or have their eyes shut. One solution may be the FEL (flash exposure lock) offered on some more expensive cameras, which allows the photographer to fire the measuring flash at some earlier time, long (many seconds) before taking the real picture. Unfortunately many camera manufacturers do not make the TTL pre-flash interval configurable.
  • Flash distracts people, limiting the number of pictures that can be taken without irritating them.
  • Photographing with flash may not be permitted in some museums even after purchasing a permit for taking pictures.
  • Flash equipment may take some time to set up, and like any grip equipment, may need to be carefully secured, especially if hanging overhead, so it does not fall on anyone. A small breeze can easily topple a flash with an umbrella on a lightstand if it is not tied down or sandbagged. Larger equipment (e.g. monoblocks) will need a supply of AC power.  

Photoelectric sensor


A photoelectric sensor, or photo eye, is an equipment used to discover the distance, absence, or presence of an object by using a light transmitter, often infrared, and a photoelectric receiver. They are largely used in industrial manufacturing. There are three different useful types: opposed (through beam), retro-reflective, and proximity-sensing (diffused).
Conceptual through-beam system to detect unauthorized access to a secure door. If the beam is damaged, the detector triggers an alarm .

Types

A self-contained photoelectric sensor contains the optics, along with the electronics. It requires only a power source. The sensor performs its own modulation, demodulation, amplification, and output switching. Some self-contained sensors provide such options as built-in control timers or counters. Because of technological progress, self-contained photoelectric sensors have become increasingly smaller.
Remote photoelectric sensors used for remote sensing contain only the optical components of a sensor. The circuitry for power input, amplification, and output switching are located elsewhere, typically in a control panel. This allows the sensor, itself, to be very small. Also, the controls for the sensor are more accessible, since they may be bigger.
When space is restricted or the environment too hostile even for remote sensors, fiber optics may be used. Fiber optics are passive mechanical sensing components. They may be used with either remote or self-contained sensors. They have no electrical circuitry and no moving parts, and can safely pipe light into and out of hostile environments.

Sensing modes

A through beam arrangement consists of a receiver located within the line-of-sight of the transmitter. In this mode, an object is detected when the light beam is blocked from getting to the receiver from the transmitter.
A retroreflective arrangement places the transmitter and receiver at the same location and uses a reflector to bounce the light beam back from the transmitter to the receiver. An object is sensed when the beam is interrupted and fails to reach the receiver.
A proximity-sensing (diffused) arrangement is one in which the transmitted radiation must reflect off the object in order to reach the receiver. In this mode, an object is detected when the receiver sees the transmitted source rather than when it fails to see it. As in retro-reflective sensors, diffuse sensor emitters and receivers are located in the same housing. But the target acts as the reflector, so that detection of light is reflected off the disturbance object. The emitter sends out a beam of light (most often a pulsed infrared, visible red, or laser) that diffuses in all directions, filling a detection area. The target then enters the area and deflects part of the beam back to the receiver. Detection occurs and output is turned on or off when sufficient light falls on the receiver.
Some photo eyes have two different operational types, light operate and dark operate. Light operate photo eyes become operational when the receiver "receives" the transmitter signal. Dark operate photo eyes become operational when the receiver "does not receive" the transmitter signal.
The detecting range of a photoelectric sensor is its "field of view", or the maximum distance from which the sensor can retrieve information, minus the minimum distance. A minimum detectable object is the smallest object the sensor can detect. More accurate sensors can often have minimum detectable objects of minuscule size.

Certain types of smoke detector use a photoelectric sensor to warn of smoldering fires.

Difference Between Modes

Name Advantages Disadvantages
Through-Beam
  • Most accurate
  • Longest sensing range
  • Very reliable
  • Must install at two points on system: emitter and receiver
  • Costly - must purchase both emitter and receiver
Reflective
  • Only slightly less accurate than through-beam
  • Sensing range better than diffuse
  • Very reliable
  • Must install at two points on system: sensor and reflector
  • Slightly more costly than diffuse
  • Sensing range less than through-beam
Diffuse
  • Only install at one point
  • Cost less than through-beam or reflective
  • Less accurate than through- beam or reflective
  • More setup time involved

   

 

List of sensors


Acoustic, sound, vibration

Automotive, transportation

Chemical

Electric current, electric potential, magnetic, radio

Environment, weather, moisture, humidity

Flow, fluid velocity

Ionizing radiation, subatomic particles

Navigation instruments

Position, angle, displacement, distance, speed, acceleration

Optical, light, imaging, photon

Pressure

Force, density, level

Thermal, heat, temperature

Proximity, presence

Sensor technology

Other sensors and sensor related properties and concepts



Photonic integrated circuit


A photonic integrated circuit (PIC) or integrated optical circuit is a device that integrates multiple (at least two) photonic functions and as such is similar to an electronic integrated circuit. The major difference between the two is that a photonic integrated circuit provides functions for information signals imposed on optical wavelengths typically in the visible spectrum or near infrared 850 nm-1650 nm.
The most commercially utilized material platform for photonic integrated circuits is indium phosphide (InP), which allows for the integration of various optically active and passive functions on the same chip. Initial examples of photonic integrated circuits were simple 2 section distributed Bragg reflector (DBR) lasers, consisting of two independently controlled device sections - a gain section and a DBR mirror section. Consequently, all modern monolithic tunable lasers, widely tunable lasers, externally modulated lasers and transmitters, integrated receivers, etc. are examples of photonic integrated circuits. Current state-of-the-art devices integrate hundreds of functions onto single chip. Pioneering work in this arena was performed at Bell Laboratories. Most notable academic centers of excellence of photonic integrated circuits in InP are the University of California at Santa Barbara, USA, and the Eindhoven University of Technology in the Netherlands.
A 2005 development showed that silicon can, even though it is an indirect bandgap material, still be used to generate laser light via the Raman nonlinearity. Such lasers are not electrically driven but optically driven and therefore still necessitate a further optical pump laser source.

Comparison to electronic integration

Unlike electronic integration where silicon is the dominant material, system photonic integrated circuits have been fabricated from a variety of material systems, including electro-optic crystals such as lithium niobate, silica on silicon, Silicon on insulator, various polymers and semiconductor materials which are used to make semiconductor lasers such as GaAs and InP. The different material systems are used because they each provide different advantages and limitations depending on the function to be integrated. For instance, silica (silicon dioxide) based PICs have very desirable properties for passive photonic circuits such as AWGs (see below) due to their comparatively low losses and low thermal sensitivity, GaAs or InP based PICs allow the direct integration of light sources and Silicon PICs enable co-integration of the photonics with transistor based electronics.
The fabrication techniques are similar to those used in electronic integrated circuits in which photolithography is used to pattern wafers for etching and material deposition. Unlike electronics where the primary device is the transistor, there is no single dominant device. The range of devices required on a chip includes low loss interconnect waveguides, power splitters, optical amplifiers, optical modulators, filters, lasers and detectors. These devices require a variety of different materials and fabrication techniques making it difficult to realize all of them on a single chip.
Newer techniques using resonant photonic interferometry is making way for UV LEDs to be used for optical computing requirements with much cheaper costs leading the way to petahertz PHz consumer electronics.

Examples of photonic integrated circuits

The primary application for photonic integrated circuits is in the area of fiber-optic communication though applications in other fields such as biomedical and photonic computing are also possible.
The arrayed waveguide grating (AWG) which are commonly used as optical (de)multiplexers in wavelength division multiplexed (WDM) fiber-optic communication systems are an example of a photonic integrated circuit which has replaced previous multiplexing schemes which utilized multiple discrete filter elements. Since separating optical modes is a need for quantum computing, this technology may be helpful to miniaturize quantum computers (see linear optical quantum computing).
Another example of a photonic integrated chip in wide use today in fiber-optic communication systems is the externally modulated laser (EML) which combines a distributed feed back laser diode with an electro-absorption modulator  on a single InP based chip.

Current status

Photonic integration is currently an active topic in U.S. Defense contracts. It is included by the Optical Internetworking Forum for inclusion in 100 gigahertz optical networking standards. 


Optical computing

                      Hasil gambar untuk electronic signal detector

Optical or photonic computing uses photons produced by lasers or diodes for computation. For decades, photons have promised to allow a higher bandwidth than the electrons used in conventional computers.
Most research projects focus on replacing current computer components with optical equivalents, resulting in an optical digital computer system processing binary data. This approach appears to offer the best short-term prospects for commercial optical computing, since optical components could be integrated into traditional computers to produce an optical-electronic hybrid. However, optoelectronic devices lose 30% of their energy converting electronic energy into photons and back; this conversion also slows the transmission of messages. All-optical computers eliminate the need for optical-electrical-optical (OEO) conversions, thus lessening the need for electrical power.
Application-specific devices, such as Synthetic aperture radar and optical correlators, have been designed to use the principles of optical computing. Correlators can be used, for example, to detect and track objects, and to classify serial time-domain optical data.

Optical components for binary digital computer

The fundamental building block of modern electronic computers is the transistor. To replace electronic components with optical ones, an equivalent optical transistor is required. This is achieved using materials with a non-linear refractive index. In particular, materials exist where the intensity of incoming light affects the intensity of the light transmitted through the material in a similar manner to the current response of a bipolar transistor. Such an 'optical transistor'  can be used to create optical logic gates, which in turn are assembled into the higher level components of the computer's CPU. These will be nonlinear optical crystals used to manipulate light beams into controlling other light beams.

Controversy

There are disagreements between researchers about the future capabilities of optical computers: will they be able to compete with semiconductor-based electronic computers on speed, power consumption, cost, and size? Critics note that  real-world logic systems require "logic-level restoration, cascadability, fan-out and input–output isolation", all of which are currently provided by electronic transistors at low cost, low power, and high speed. For optical logic to be competitive beyond a few niche applications, major breakthroughs in non-linear optical device technology would be required, or perhaps a change in the nature of computing itself.

Misconceptions, challenges, and prospects

A significant challenge to optical computing is that computation is a nonlinear process in which multiple signals must interact. Light, which is an electromagnetic wave, can only interact with another electromagnetic wave in the presence of electrons in a material, and the strength of this interaction is much weaker for electromagnetic waves, such as light, than for the electronic signals in a conventional computer. This may result in the processing elements for an optical computer requiring more power and larger dimensions than those for a conventional electronic computer using transistors.
A further misconception is that since light can travel much faster than the drift velocity of electrons, and at frequencies measured in THz, optical transistors should be capable of extremely high frequencies. However, any electromagnetic wave must obey the transform limit, and therefore the rate at which an optical transistor can respond to a signal is still limited by its spectral bandwidth. However, in fiber optic communications, practical limits such as dispersion often constrain channels to bandwidths of 10s of GHz, only slightly better than many silicon transistors. Obtaining dramatically faster operation than electronic transistors would therefore require practical methods of transmitting ultrashort pulses down highly dispersive waveguides.

Photonic logic

Realization of a Photonic Controlled-NOT Gate for use in Quantum Computing 

Photonic logic is the use of photons (light) in logic gates (NOT, AND, OR, NAND, NOR, XOR, XNOR). Switching is obtained using nonlinear optical effects when two or more signals are combined.
Resonators are especially useful in photonic logic, since they allow a build-up of energy from constructive interference, thus enhancing optical nonlinear effects.
Other approaches currently being investigated include photonic logic at a molecular level, using photoluminescent chemicals. In a recent demonstration, Witlicki et al. performed logical operations using molecules and SERS.

Optical fiber


A bundle of optical fibers
 
Fiber crew installing a 432-count fiber cable underneath the streets of Midtown Manhattan, New York City 

A TOSLINK fiber optic audio cable with red light being shone in one end transmits the light to the other end 

A wall-mount cabinet containing optical fiber interconnects. The yellow cables are single mode fibers; the orange and aqua cables are multi-mode fibers: 50/125 µm OM2 and 50/125 µm OM3 fibers respectively. 

An optical fiber or optical fibre is a flexible, transparent fiber made by drawing glass (silica) or plastic to a diameter slightly thicker than that of a human hair. Optical fibers are used most often as a means to transmit light between the two ends of the fiber and find wide usage in fiber-optic communications, where they permit transmission over longer distances and at higher bandwidths (data rates) than wire cables. Fibers are used instead of metal wires because signals travel along them with lesser amounts of loss; in addition, fibers are also immune to electromagnetic interference, a problem from which metal wires suffer excessively. Fibers are also used for illumination, and are wrapped in bundles so that they may be used to carry images, thus allowing viewing in confined spaces, as in the case of a fiberscope. Specially designed fibers are also used for a variety of other applications, some of them being fiber optic sensors and fiber lasers.
Optical fibers typically include a transparent core surrounded by a transparent cladding material with a lower index of refraction. Light is kept in the core by the phenomenon of total internal reflection which causes the fiber to act as a waveguide. Fibers that support many propagation paths or transverse modes are called multi-mode fibers (MMF), while those that support a single mode are called single-mode fibers (SMF). Multi-mode fibers generally have a wider core diameter and are used for short-distance communication links and for applications where high power must be transmitted. Single-mode fibers are used for most communication links longer than 1,000 meters (3,300 ft).
Being able to join optical fibers with low loss is important in fiber optic communication. This is more complex than joining electrical wire or cable and involves careful cleaving of the fibers, precise alignment of the fiber cores, and the coupling of these aligned cores. For applications that demand a permanent connection a fusion splice is common. In this technique, an electric arc is used to melt the ends of the fibers together. Another common technique is a mechanical splice, where the ends of the fibers are held in contact by mechanical force. Temporary or semi-permanent connections are made by means of specialized optical fiber connectors.
The field of applied science and engineering concerned with the design and application of optical fibers is known as fiber optics. The term was coined by Indian physicist Narinder Singh Kapany who is widely acknowledged as the father of fiber optics.

a bright cloud

Daniel Colladon first described this “light fountain” or “light pipe” in an 1842 article titled On the reflections of a ray of light inside a parabolic liquid stream. This particular illustration comes from a later article by Colladon, in 1884.

Record speeds

Achieving a high data rate and covering a long distance simultaneously is challenging. To express this, sometimes the product of data rate and distance is specified – (bit/s)×km or the equivalent bit×km/s, similar to the bandwidth-distance product.
  • 2006Nippon Telegraph and Telephone Corporation transferred 14 terabits per second over a single 160 km long optical fiber
  • 2009Bell Labs in Villarceaux, France transferred 100 Gbit/s over 7000 km fiber
  • 2010 – Nippon Telegraph and Telephone Corporation transferred 69.1 Tbit/s over a single 240 km fiber multiplexing 432 channels, equating to 171 Gbit/s per channel
  • 2012 – Nippon Telegraph and Telephone Corporation transferred 1 Petabit per second over 50 kilometers over a single fiber

Uses

Communication

Optical fiber can be used as a medium for telecommunication and computer networking because it is flexible and can be bundled as cables. It is especially advantageous for long-distance communications, because light propagates through the fiber with little attenuation compared to electrical cables. This allows long distances to be spanned with few repeaters.
The per-channel light signals propagating in the fiber have been modulated at rates as high as 111 gigabits per second (Gbit/s) by NTT, although 10 or 40 Gbit/s is typical in deployed systems. In June 2013, researchers demonstrated transmission of 400 Gbit/s over a single channel using 4-mode orbital angular momentum multiplexing.
Each fiber can carry many independent channels, each using a different wavelength of light (wavelength-division multiplexing (WDM)). The net data rate (data rate without overhead bytes) per fiber is the per-channel data rate reduced by the FEC overhead, multiplied by the number of channels (usually up to eighty in commercial dense WDM systems as of 2008). As of 2011 the record for bandwidth on a single core was 101 Tbit/s (370 channels at 273 Gbit/s each). The record for a multi-core fiber as of January 2013 was 1.05 petabits per second.  In 2009, Bell Labs broke the 100 (petabit per second)×kilometer barrier (15.5 Tbit/s over a single 7,000 km fiber).
For short-distance applications, such as a network in an office building (see FTTO), fiber-optic cabling can save space in cable ducts. This is because a single fiber can carry much more data than electrical cables such as standard category 5 Ethernet cabling, which typically runs at 100 Mbit/s or 1 Gbit/s speeds. Fiber is also immune to electrical interference; there is no cross-talk between signals in different cables, and no pickup of environmental noise. Non-armored fiber cables do not conduct electricity, which makes fiber a good solution for protecting communications equipment in high voltage environments, such as power generation facilities, or metal communication structures prone to lightning strikes. They can also be used in environments where explosive fumes are present, without danger of ignition. Wiretapping (in this case, fiber tapping) is more difficult compared to electrical connections, and there are concentric dual-core fibers that are said to be tap-proof.
Fibers are often also used for short-distance connections between devices. For example, most high-definition televisions offer a digital audio optical connection. This allows the streaming of audio over light, using the TOSLINK protocol.

The advantages of optical fiber communication with respect to copper wire systems are:

  • Broad bandwidth: A single optical fiber can carry over 3,000,000 full-duplex voice calls or 90,000 TV channels.
  • Immunity to electromagnetic interference: Light transmission through optical fibers is unaffected by other electromagnetic radiation nearby. The optical fiber is electrically non-conductive, so it does not act as an antenna to pick up electromagnetic signals. Information traveling inside the optical fiber is immune to electromagnetic interference, even electromagnetic pulses generated by nuclear devices.
  • Low attenuation loss over long distances: Attenuation loss can be as low as 0.2 dB/km in optical fiber cables, allowing transmission over long distances without the need for repeaters.
  • Electrical insulator: Optical fibers do not conduct electricity, preventing problems with ground loops and conduction of lightning. Optical fibers can be strung on poles alongside high voltage power cables.
  • Material cost and theft prevention: Conventional cable systems use large amounts of copper. Global copper prices experienced a boom in the 2000s, and copper has been a target of metal theft.
  • Security of information passed down the cable: Copper can be tapped with very little chance of detection.

Sensors

Fibers have many uses in remote sensing. In some applications, the sensor is itself an optical fiber. In other cases, fiber is used to connect a non-fiberoptic sensor to a measurement system. Depending on the application, fiber may be used because of its small size, or the fact that no electrical power is needed at the remote location, or because many sensors can be multiplexed along the length of a fiber by using different wavelengths of light for each sensor, or by sensing the time delay as light passes along the fiber through each sensor. Time delay can be determined using a device such as an optical time-domain reflectometer.
Optical fibers can be used as sensors to measure strain, temperature, pressure and other quantities by modifying a fiber so that the property to measure modulates the intensity, phase, polarization, wavelength, or transit time of light in the fiber. Sensors that vary the intensity of light are the simplest, since only a simple source and detector are required. A particularly useful feature of such fiber optic sensors is that they can, if required, provide distributed sensing over distances of up to one meter. In contrast, highly localized measurements can be provided by integrating miniaturized sensing elements with the tip of the fiber.  These can be implemented by various micro- and nanofabrication technologies, such that they do not exceed the microscopic boundary of the fiber tip, allowing such applications as insertion into blood vessels via hypodermic needle.
Extrinsic fiber optic sensors use an optical fiber cable, normally a multi-mode one, to transmit modulated light from either a non-fiber optical sensor—or an electronic sensor connected to an optical transmitter. A major benefit of extrinsic sensors is their ability to reach otherwise inaccessible places. An example is the measurement of temperature inside aircraft jet engines by using a fiber to transmit radiation into a radiation pyrometer outside the engine. Extrinsic sensors can be used in the same way to measure the internal temperature of electrical transformers, where the extreme electromagnetic fields present make other measurement techniques impossible. Extrinsic sensors measure vibration, rotation, displacement, velocity, acceleration, torque, and twisting. A solid state version of the gyroscope, using the interference of light, has been developed. The fiber optic gyroscope (FOG) has no moving parts, and exploits the Sagnac effect to detect mechanical rotation.
Common uses for fiber optic sensors includes advanced intrusion detection security systems. The light is transmitted along a fiber optic sensor cable placed on a fence, pipeline, or communication cabling, and the returned signal is monitored and analyzed for disturbances. This return signal is digitally processed to detect disturbances and trip an alarm if an intrusion has occurred.
Optical fibers are widely used as components of optical chemical sensors and optical biosensors.

Power transmission

Optical fiber can be used to transmit power using a photovoltaic cell to convert the light into electricity. While this method of power transmission is not as efficient as conventional ones, it is especially useful in situations where it is desirable not to have a metallic conductor as in the case of use near MRI machines, which produce strong magnetic fields. Other examples are for powering electronics in high-powered antenna elements and measurement devices used in high-voltage transmission equipment.

Other uses

A frisbee illuminated by fiber optics
 
Light reflected from optical fiber illuminates exhibited model 

Optical fibers have a wide number of applications. They are used as light guides in medical and other applications where bright light needs to be shone on a target without a clear line-of-sight path. In some buildings, optical fibers route sunlight from the roof to other parts of the building (see nonimaging optics). Optical fiber lamps are used for illumination in decorative applications, including signs, art, toys and artificial Christmas trees. Swarovski boutiques use optical fibers to illuminate their crystal showcases from many different angles while only employing one light source. Optical fiber is an intrinsic part of the light-transmitting concrete building product, LiTraCon.

Use of optical fiber in a decorative lamp or nightlight. 

Optical fiber is also used in imaging optics. A coherent bundle of fibers is used, sometimes along with lenses, for a long, thin imaging device called an endoscope, which is used to view objects through a small hole. Medical endoscopes are used for minimally invasive exploratory or surgical procedures. Industrial endoscopes (see fiberscope or borescope) are used for inspecting anything hard to reach, such as jet engine interiors. Many microscopes use fiber-optic light sources to provide intense illumination of samples being studied.
In spectroscopy, optical fiber bundles transmit light from a spectrometer to a substance that cannot be placed inside the spectrometer itself, in order to analyze its composition. A spectrometer analyzes substances by bouncing light off and through them. By using fibers, a spectrometer can be used to study objects remotely.
An optical fiber doped with certain rare earth elements such as erbium can be used as the gain medium of a laser or optical amplifier. Rare-earth-doped optical fibers can be used to provide signal amplification by splicing a short section of doped fiber into a regular (undoped) optical fiber line. The doped fiber is optically pumped with a second laser wavelength that is coupled into the line in addition to the signal wave. Both wavelengths of light are transmitted through the doped fiber, which transfers energy from the second pump wavelength to the signal wave. The process that causes the amplification is stimulated emission.
Optical fiber is also widely exploited as a nonlinear medium. The glass medium supports a host of nonlinear optical interactions, and the long interaction lengths possible in fiber facilitate a variety of phenomena, which are harnessed for applications and fundamental investigation. Conversely, fiber nonlinearity can have deleterious effects on optical signals, and measures are often required to minimize such unwanted effects.
Optical fibers doped with a wavelength shifter collect scintillation light in physics experiments.
Fiber optic sights for handguns, rifles, and shotguns use pieces of optical fiber to improve visibility of markings on the sight.

Principle of operation

An overview of the operating principles of the optical fiber
An optical fiber is a cylindrical dielectric waveguide (nonconducting waveguide) that transmits light along its axis, by the process of total internal reflection. The fiber consists of a core surrounded by a cladding layer, both of which are made of dielectric materials. To confine the optical signal in the core, the refractive index of the core must be greater than that of the cladding. The boundary between the core and cladding may either be abrupt, in step-index fiber, or gradual, in graded-index fiber.

Index of refraction

The index of refraction (or refractive index) is a way of measuring the speed of light in a material. Light travels fastest in a vacuum, such as in outer space. The speed of light in a vacuum is about 300,000 kilometers (186,000 miles) per second. The refractive index of a medium is calculated by dividing the speed of light in a vacuum by the speed of light in that medium. The refractive index of a vacuum is therefore 1, by definition. A typical singlemode fiber used for telecommunications has a cladding made of pure silica, with an index of 1.444 at 1,500 nm, and a core of doped silica with an index around 1.4475. The larger the index of refraction, the slower light travels in that medium. From this information, a simple rule of thumb is that a signal using optical fiber for communication will travel at around 200,000 kilometers per second. To put it another way, the signal will take 5 milliseconds to travel 1,000 kilometers in fiber. Thus a phone call carried by fiber between Sydney and New York, a 16,000-kilometer distance, means that there is a minimum delay of 80 milliseconds (about {\tfrac {1}{12}} of a second) between when one caller speaks and the other hears. (The fiber in this case will probably travel a longer route, and there will be additional delays due to communication equipment switching and the process of encoding and decoding the voice onto the fiber).

Total internal reflection

When light traveling in an optically dense medium hits a boundary at a steep angle (larger than the critical angle for the boundary), the light is completely reflected. This is called total internal reflection. This effect is used in optical fibers to confine light in the core. Light travels through the fiber core, bouncing back and forth off the boundary between the core and cladding. Because the light must strike the boundary with an angle greater than the critical angle, only light that enters the fiber within a certain range of angles can travel down the fiber without leaking out. This range of angles is called the acceptance cone of the fiber. The size of this acceptance cone is a function of the refractive index difference between the fiber's core and cladding.
In simpler terms, there is a maximum angle from the fiber axis at which light may enter the fiber so that it will propagate, or travel, in the core of the fiber. The sine of this maximum angle is the numerical aperture (NA) of the fiber. Fiber with a larger NA requires less precision to splice and work with than fiber with a smaller NA. Single-mode fiber has a small NA.

Multi-mode fiber

The propagation of light through a multi-mode optical fiber

A laser bouncing down an acrylic rod, illustrating the total internal reflection of light in a multi-mode optical fiber.
 
Fiber with large core diameter (greater than 10 micrometers) may be analyzed by geometrical optics. Such fiber is called multi-mode fiber, from the electromagnetic analysis (see below). In a step-index multi-mode fiber, rays of light are guided along the fiber core by total internal reflection. Rays that meet the core-cladding boundary at a high angle (measured relative to a line normal to the boundary), greater than the critical angle for this boundary, are completely reflected. The critical angle (minimum angle for total internal reflection) is determined by the difference in index of refraction between the core and cladding materials. Rays that meet the boundary at a low angle are refracted from the core into the cladding, and do not convey light and hence information along the fiber. The critical angle determines the acceptance angle of the fiber, often reported as a numerical aperture. A high numerical aperture allows light to propagate down the fiber in rays both close to the axis and at various angles, allowing efficient coupling of light into the fiber. However, this high numerical aperture increases the amount of dispersion as rays at different angles have different path lengths and therefore take different times to traverse the fiber.

Optical fiber types.
 
In graded-index fiber, the index of refraction in the core decreases continuously between the axis and the cladding. This causes light rays to bend smoothly as they approach the cladding, rather than reflecting abruptly from the core-cladding boundary. The resulting curved paths reduce multi-path dispersion because high angle rays pass more through the lower-index periphery of the core, rather than the high-index center. The index profile is chosen to minimize the difference in axial propagation speeds of the various rays in the fiber. This ideal index profile is very close to a parabolic relationship between the index and the distance from the axis.

Single-mode fiber

The structure of a typical single-mode fiber

1. Core: 8 Âµm diameter
2. Cladding: 125 Âµm dia.
3. Buffer: 250 Âµm dia.
4. Jacket: 400 Âµm dia. 

Fiber with a core diameter less than about ten times the wavelength of the propagating light cannot be modeled using geometric optics. Instead, it must be analyzed as an electromagnetic structure, by solution of Maxwell's equations as reduced to the electromagnetic wave equation. The electromagnetic analysis may also be required to understand behaviors such as speckle that occur when coherent light propagates in multi-mode fiber. As an optical waveguide, the fiber supports one or more confined transverse modes by which light can propagate along the fiber. Fiber supporting only one mode is called single-mode or mono-mode fiber. The behavior of larger-core multi-mode fiber can also be modeled using the wave equation, which shows that such fiber supports more than one mode of propagation (hence the name). The results of such modeling of multi-mode fiber approximately agree with the predictions of geometric optics, if the fiber core is large enough to support more than a few modes.
The waveguide analysis shows that the light energy in the fiber is not completely confined in the core. Instead, especially in single-mode fibers, a significant fraction of the energy in the bound mode travels in the cladding as an evanescent wave.
The most common type of single-mode fiber has a core diameter of 8–10 micrometers and is designed for use in the near infrared. The mode structure depends on the wavelength of the light used, so that this fiber actually supports a small number of additional modes at visible wavelengths. Multi-mode fiber, by comparison, is manufactured with core diameters as small as 50 micrometers and as large as hundreds of micrometers. The normalized frequency V for this fiber should be less than the first zero of the Bessel function J0 (approximately 2.405).

Special-purpose fiber

Some special-purpose optical fiber is constructed with a non-cylindrical core and/or cladding layer, usually with an elliptical or rectangular cross-section. These include polarization-maintaining fiber and fiber designed to suppress whispering gallery mode propagation. Polarization-maintaining fiber is a unique type of fiber that is commonly used in fiber optic sensors due to its ability to maintain the polarization of the light inserted into it.
Photonic-crystal fiber is made with a regular pattern of index variation (often in the form of cylindrical holes that run along the length of the fiber). Such fiber uses diffraction effects instead of or in addition to total internal reflection, to confine light to the fiber's core. The properties of the fiber can be tailored to a wide variety of applications.

Mechanisms of attenuation

Light attenuation by ZBLAN and silica fibers


Attenuation in fiber optics, also known as transmission loss, is the reduction in intensity of the light beam (or signal) as it travels through the transmission medium. Attenuation coefficients in fiber optics usually use units of dB/km through the medium due to the relatively high quality of transparency of modern optical transmission media. The medium is usually a fiber of silica glass that confines the incident light beam to the inside. Attenuation is an important factor limiting the transmission of a digital signal across large distances. Thus, much research has gone into both limiting the attenuation and maximizing the amplification of the optical signal. Empirical research has shown that attenuation in optical fiber is caused primarily by both scattering and absorption. Single-mode optical fibers can be made with extremely low loss. Corning's SMF-28 fiber, a standard single-mode fiber for telecommunications wavelengths, has a loss of 0.17 dB/km at 1550 nm. For example, an 8 km length of SMF-28 transmits nearly 75% of light at 1,550 nm. It has been noted that if ocean water was as clear as fiber, one could see all the way to the bottom even of the Marianas Trench in the Pacific Ocean, a depth of 36,000 feet.

Light scattering

Specular reflection
Diffuse reflection
The propagation of light through the core of an optical fiber is based on total internal reflection of the lightwave. Rough and irregular surfaces, even at the molecular level, can cause light rays to be reflected in random directions. This is called diffuse reflection or scattering, and it is typically characterized by wide variety of reflection angles.
Light scattering depends on the wavelength of the light being scattered. Thus, limits to spatial scales of visibility arise, depending on the frequency of the incident light-wave and the physical dimension (or spatial scale) of the scattering center, which is typically in the form of some specific micro-structural feature. Since visible light has a wavelength of the order of one micrometer (one millionth of a meter) scattering centers will have dimensions on a similar spatial scale.
Thus, attenuation results from the incoherent scattering of light at internal surfaces and interfaces. In (poly)crystalline materials such as metals and ceramics, in addition to pores, most of the internal surfaces or interfaces are in the form of grain boundaries that separate tiny regions of crystalline order. It has recently been shown that when the size of the scattering center (or grain boundary) is reduced below the size of the wavelength of the light being scattered, the scattering no longer occurs to any significant extent. This phenomenon has given rise to the production of transparent ceramic materials.
Similarly, the scattering of light in optical quality glass fiber is caused by molecular level irregularities (compositional fluctuations) in the glass structure. Indeed, one emerging school of thought is that a glass is simply the limiting case of a polycrystalline solid. Within this framework, "domains" exhibiting various degrees of short-range order become the building blocks of both metals and alloys, as well as glasses and ceramics. Distributed both between and within these domains are micro-structural defects that provide the most ideal locations for light scattering. This same phenomenon is seen as one of the limiting factors in the transparency of IR missile domes.
At high optical powers, scattering can also be caused by nonlinear optical processes in the fiber.

UV-Vis-IR absorption

In addition to light scattering, attenuation or signal loss can also occur due to selective absorption of specific wavelengths, in a manner similar to that responsible for the appearance of color. Primary material considerations include both electrons and molecules as follows:
  • At the electronic level, it depends on whether the electron orbitals are spaced (or "quantized") such that they can absorb a quantum of light (or photon) of a specific wavelength or frequency in the ultraviolet (UV) or visible ranges. This is what gives rise to color.
  • At the atomic or molecular level, it depends on the frequencies of atomic or molecular vibrations or chemical bonds, how close-packed its atoms or molecules are, and whether or not the atoms or molecules exhibit long-range order. These factors will determine the capacity of the material transmitting longer wavelengths in the infrared (IR), far IR, radio and microwave ranges.
The design of any optically transparent device requires the selection of materials based upon knowledge of its properties and limitations. The Lattice absorption characteristics observed at the lower frequency regions (mid IR to far-infrared wavelength range) define the long-wavelength transparency limit of the material. They are the result of the interactive coupling between the motions of thermally induced vibrations of the constituent atoms and molecules of the solid lattice and the incident light wave radiation. Hence, all materials are bounded by limiting regions of absorption caused by atomic and molecular vibrations (bond-stretching)in the far-infrared (>10 Âµm).
Thus, multi-phonon absorption occurs when two or more phonons simultaneously interact to produce electric dipole moments with which the incident radiation may couple. These dipoles can absorb energy from the incident radiation, reaching a maximum coupling with the radiation when the frequency is equal to the fundamental vibrational mode of the molecular dipole (e.g. Si-O bond) in the far-infrared, or one of its harmonics.
The selective absorption of infrared (IR) light by a particular material occurs because the selected frequency of the light wave matches the frequency (or an integer multiple of the frequency) at which the particles of that material vibrate. Since different atoms and molecules have different natural frequencies of vibration, they will selectively absorb different frequencies (or portions of the spectrum) of infrared (IR) light.
Reflection and transmission of light waves occur because the frequencies of the light waves do not match the natural resonant frequencies of vibration of the objects. When IR light of these frequencies strikes an object, the energy is either reflected or transmitted.

Manufacturing

Materials

Glass optical fibers are almost always made from silica, but some other materials, such as fluorozirconate, fluoroaluminate, and chalcogenide glasses as well as crystalline materials like sapphire, are used for longer-wavelength infrared or other specialized applications. Silica and fluoride glasses usually have refractive indices of about 1.5, but some materials such as the chalcogenides can have indices as high as 3. Typically the index difference between core and cladding is less than one percent.
Plastic optical fibers (POF) are commonly step-index multi-mode fibers with a core diameter of 0.5 millimeters or larger. POF typically have higher attenuation coefficients than glass fibers, 1 dB/m or higher, and this high attenuation limits the range of POF-based systems.

Silica

Silica exhibits fairly good optical transmission over a wide range of wavelengths. In the near-infrared (near IR) portion of the spectrum, particularly around 1.5 μm, silica can have extremely low absorption and scattering losses of the order of 0.2 dB/km. Such remarkably low losses are possible only because ultra-pure silicon is available, it being essential for manufacturing integrated circuits and discrete transistors. A high transparency in the 1.4-μm region is achieved by maintaining a low concentration of hydroxyl groups (OH). Alternatively, a high OH concentration is better for transmission in the ultraviolet (UV) region.
Silica can be drawn into fibers at reasonably high temperatures, and has a fairly broad glass transformation range. One other advantage is that fusion splicing and cleaving of silica fibers is relatively effective. Silica fiber also has high mechanical strength against both pulling and even bending, provided that the fiber is not too thick and that the surfaces have been well prepared during processing. Even simple cleaving (breaking) of the ends of the fiber can provide nicely flat surfaces with acceptable optical quality. Silica is also relatively chemically inert. In particular, it is not hygroscopic (does not absorb water).
Silica glass can be doped with various materials. One purpose of doping is to raise the refractive index (e.g. with germanium dioxide (GeO2) or aluminium oxide (Al2O3)) or to lower it (e.g. with fluorine or boron trioxide (B2O3)). Doping is also possible with laser-active ions (for example, rare earth-doped fibers) in order to obtain active fibers to be used, for example, in fiber amplifiers or laser applications. Both the fiber core and cladding are typically doped, so that the entire assembly (core and cladding) is effectively the same compound (e.g. an aluminosilicate, germanosilicate, phosphosilicate or borosilicate glass).
Particularly for active fibers, pure silica is usually not a very suitable host glass, because it exhibits a low solubility for rare earth ions. This can lead to quenching effects due to clustering of dopant ions. Aluminosilicates are much more effective in this respect.
Silica fiber also exhibits a high threshold for optical damage. This property ensures a low tendency for laser-induced breakdown. This is important for fiber amplifiers when utilized for the amplification of short pulses.
Because of these properties silica fibers are the material of choice in many optical applications, such as communications (except for very short distances with plastic optical fiber), fiber lasers, fiber amplifiers, and fiber-optic sensors. Large efforts put forth in the development of various types of silica fibers have further increased the performance of such fibers over other materials.

Fluoride glass

Fluoride glass is a class of non-oxide optical quality glasses composed of fluorides of various metals. Because of their low viscosity, it is very difficult to completely avoid crystallization while processing it through the glass transition (or drawing the fiber from the melt). Thus, although heavy metal fluoride glasses (HMFG) exhibit very low optical attenuation, they are not only difficult to manufacture, but are quite fragile, and have poor resistance to moisture and other environmental attacks. Their best attribute is that they lack the absorption band associated with the hydroxyl (OH) group (3,200–3,600 cm−1; i.e., 2,777–3,125 nm or 2.78–3.13 μm), which is present in nearly all oxide-based glasses.
An example of a heavy metal fluoride glass is the ZBLAN glass group, composed of zirconium, barium, lanthanum, aluminium, and sodium fluorides. Their main technological application is as optical waveguides in both planar and fiber form. They are advantageous especially in the mid-infrared (2,000–5,000 nm) range.
HMFGs were initially slated for optical fiber applications, because the intrinsic losses of a mid-IR fiber could in principle be lower than those of silica fibers, which are transparent only up to about 2 μm. However, such low losses were never realized in practice, and the fragility and high cost of fluoride fibers made them less than ideal as primary candidates. Later, the utility of fluoride fibers for various other applications was discovered. These include mid-IR spectroscopy, fiber optic sensors, thermometry, and imaging. Also, fluoride fibers can be used for guided lightwave transmission in media such as YAG (yttrium aluminium garnet) lasers at 2.9 μm, as required for medical applications (e.g. ophthalmology and dentistry).

Phosphate glass

The P4O10 cagelike structure—the basic building block for phosphate glass.
Phosphate glass constitutes a class of optical glasses composed of metaphosphates of various metals. Instead of the SiO4 tetrahedra observed in silicate glasses, the building block for this glass former is phosphorus pentoxide (P2O5), which crystallizes in at least four different forms. The most familiar polymorph (see figure) comprises molecules of P4O10.
Phosphate glasses can be advantageous over silica glasses for optical fibers with a high concentration of doping rare earth ions. A mix of fluoride glass and phosphate glass is fluorophosphate glass.

Chalcogenide glass

The chalcogens—the elements in group 16 of the periodic table—particularly sulfur (S), selenium (Se) and tellurium (Te)—react with more electropositive elements, such as silver, to form chalcogenides. These are extremely versatile compounds, in that they can be crystalline or amorphous, metallic or semiconducting, and conductors of ions or electrons. Glass containing chalcogenides can be used to make fibers for far infrared transmission.[citation needed]

Process

Preform

Illustration of the modified chemical vapor deposition (inside) process
Standard optical fibers are made by first constructing a large-diameter "preform" with a carefully controlled refractive index profile, and then "pulling" the preform to form the long, thin optical fiber. The preform is commonly made by three chemical vapor deposition methods: inside vapor deposition, outside vapor deposition, and vapor axial deposition.
With inside vapor deposition, the preform starts as a hollow glass tube approximately 40 centimeters (16 in) long, which is placed horizontally and rotated slowly on a lathe. Gases such as silicon tetrachloride (SiCl4) or germanium tetrachloride (GeCl4) are injected with oxygen in the end of the tube. The gases are then heated by means of an external hydrogen burner, bringing the temperature of the gas up to 1,900 K (1,600 °C, 3,000 °F), where the tetrachlorides react with oxygen to produce silica or germania (germanium dioxide) particles. When the reaction conditions are chosen to allow this reaction to occur in the gas phase throughout the tube volume, in contrast to earlier techniques where the reaction occurred only on the glass surface, this technique is called modified chemical vapor deposition (MCVD).
The oxide particles then agglomerate to form large particle chains, which subsequently deposit on the walls of the tube as soot. The deposition is due to the large difference in temperature between the gas core and the wall causing the gas to push the particles outwards (this is known as thermophoresis). The torch is then traversed up and down the length of the tube to deposit the material evenly. After the torch has reached the end of the tube, it is then brought back to the beginning of the tube and the deposited particles are then melted to form a solid layer. This process is repeated until a sufficient amount of material has been deposited. For each layer the composition can be modified by varying the gas composition, resulting in precise control of the finished fiber's optical properties.
In outside vapor deposition or vapor axial deposition, the glass is formed by flame hydrolysis, a reaction in which silicon tetrachloride and germanium tetrachloride are oxidized by reaction with water (H2O) in an oxyhydrogen flame. In outside vapor deposition the glass is deposited onto a solid rod, which is removed before further processing. In vapor axial deposition, a short seed rod is used, and a porous preform, whose length is not limited by the size of the source rod, is built up on its end. The porous preform is consolidated into a transparent, solid preform by heating to about 1,800 K (1,500 °C, 2,800 °F).

Cross-section of a fiber drawn from a D-shaped preform 

Typical communications fiber uses a circular preform. For some applications such as double-clad fibers another form is preferred. In fiber lasers based on double-clad fiber, an asymmetric shape improves the filling factor for laser pumping.
Because of the surface tension, the shape is smoothed during the drawing process, and the shape of the resulting fiber does not reproduce the sharp edges of the preform. Nevertheless, careful polishing of the preform is important, since any defects of the preform surface affect the optical and mechanical properties of the resulting fiber. In particular, the preform for the test-fiber shown in the figure was not polished well, and cracks are seen with the confocal optical microscope.

Drawing

The preform, however constructed, is placed in a device known as a drawing tower, where the preform tip is heated and the optical fiber is pulled out as a string. By measuring the resultant fiber width, the tension on the fiber can be controlled to maintain the fiber thickness.

Coatings

The light is guided down the core of the fiber by an optical cladding with a lower refractive index that traps light in the core through total internal reflection.
The cladding is coated by a buffer that protects it from moisture and physical damage.[65] The buffer coating is what gets stripped off the fiber for termination or splicing. These coatings are UV-cured urethane acrylate composite or polyimide materials applied to the outside of the fiber during the drawing process. The coatings protect the very delicate strands of glass fiber—about the size of a human hair—and allow it to survive the rigors of manufacturing, proof testing, cabling and installation.
Today’s glass optical fiber draw processes employ a dual-layer coating approach. An inner primary coating is designed to act as a shock absorber to minimize attenuation caused by microbending. An outer secondary coating protects the primary coating against mechanical damage and acts as a barrier to lateral forces, and may be colored to differentiate strands in bundled cable constructions.
These fiber optic coating layers are applied during the fiber draw, at speeds approaching 100 kilometers per hour (60 mph). Fiber optic coatings are applied using one of two methods: wet-on-dry and wet-on-wet. In wet-on-dry, the fiber passes through a primary coating application, which is then UV cured—then through the secondary coating application, which is subsequently cured. In wet-on-wet, the fiber passes through both the primary and secondary coating applications, then goes to UV curing.
Fiber optic coatings are applied in concentric layers to prevent damage to the fiber during the drawing application and to maximize fiber strength and microbend resistance. Unevenly coated fiber will experience non-uniform forces when the coating expands or contracts, and is susceptible to greater signal attenuation. Under proper drawing and coating processes, the coatings are concentric around the fiber, continuous over the length of the application and have constant thickness.
Fiber optic coatings protect the glass fibers from scratches that could lead to strength degradation. The combination of moisture and scratches accelerates the aging and deterioration of fiber strength. When fiber is subjected to low stresses over a long period, fiber fatigue can occur. Over time or in extreme conditions, these factors combine to cause microscopic flaws in the glass fiber to propagate, which can ultimately result in fiber failure.
Three key characteristics of fiber optic waveguides can be affected by environmental conditions: strength, attenuation and resistance to losses caused by microbending. External optical fiber cable jackets and buffer tubes protect glass optical fiber from environmental conditions that can affect the fiber’s performance and long-term durability. On the inside, coatings ensure the reliability of the signal being carried and help minimize attenuation due to microbending.

Practical issues

Cable construction

In practical fibers, the cladding is usually coated with a tough resin coating and an additional buffer layer, which may be further surrounded by a jacket layer, usually plastic. These layers add strength to the fiber but do not contribute to its optical wave guide properties. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications.
Modern cables come in a wide variety of sheathings and armor, designed for applications such as direct burial in trenches, high voltage isolation, dual use as power lines, installation in conduit, lashing to aerial telephone poles, submarine installation, and insertion in paved streets. Multi-fiber cable usually uses colored coatings and/or buffers to identify each strand. The cost of small fiber-count pole-mounted cables has greatly decreased due to the high demand for fiber to the home (FTTH) installations in Japan and South Korea.
Fiber cable can be very flexible, but traditional fiber's loss increases greatly if the fiber is bent with a radius smaller than around 30 mm. This creates a problem when the cable is bent around corners or wound around a spool, making FTTX installations more complicated. "Bendable fibers", targeted towards easier installation in home environments, have been standardized as ITU-T G.657. This type of fiber can be bent with a radius as low as 7.5 mm without adverse impact. Even more bendable fibers have been developed. Bendable fiber may also be resistant to fiber hacking, in which the signal in a fiber is surreptitiously monitored by bending the fiber and detecting the leakage.
Another important feature of cable is cable's ability to withstand horizontally applied force. It is technically called max tensile strength defining how much force can be applied to the cable during the installation period.
Some fiber optic cable versions are reinforced with aramid yarns or glass yarns as intermediary strength member. In commercial terms, usage of the glass yarns are more cost effective while no loss in mechanical durability of the cable. Glass yarns also protect the cable core against rodents and termites.

Termination and splicing

Optical fibers are connected to terminal equipment by optical fiber connectors. These connectors are usually of a standard type such as FC, SC, ST, LC, MTRJ, or SMA. Optical fibers may be connected to each other by connectors or by splicing, that is, joining two fibers together to form a continuous optical waveguide. The generally accepted splicing method is arc fusion splicing, which melts the fiber ends together with an electric arc. For quicker fastening jobs, a “mechanical splice” is used.
Fusion splicing is done with a specialized instrument. The fiber ends are first stripped of their protective polymer coating (as well as the more sturdy outer jacket, if present). The ends are cleaved (cut) with a precision cleaver to make them perpendicular, and are placed into special holders in the fusion splicer. The splice is usually inspected via a magnified viewing screen to check the cleaves before and after the splice. The splicer uses small motors to align the end faces together, and emits a small spark between electrodes at the gap to burn off dust and moisture. Then the splicer generates a larger spark that raises the temperature above the melting point of the glass, fusing the ends together permanently. The location and energy of the spark is carefully controlled so that the molten core and cladding do not mix, and this minimizes optical loss. A splice loss estimate is measured by the splicer, by directing light through the cladding on one side and measuring the light leaking from the cladding on the other side. A splice loss under 0.1 dB is typical. The complexity of this process makes fiber splicing much more difficult than splicing copper wire.
Mechanical fiber splices are designed to be quicker and easier to install, but there is still the need for stripping, careful cleaning and precision cleaving. The fiber ends are aligned and held together by a precision-made sleeve, often using a clear index-matching gel that enhances the transmission of light across the joint. Such joints typically have higher optical loss and are less robust than fusion splices, especially if the gel is used. All splicing techniques involve installing an enclosure that protects the splice.
Fibers are terminated in connectors that hold the fiber end precisely and securely. A fiber-optic connector is basically a rigid cylindrical barrel surrounded by a sleeve that holds the barrel in its mating socket. The mating mechanism can be push and click, turn and latch (bayonet mount), or screw-in (threaded). The barrel is typically free to move within the sleeve, and may have a key that prevents the barrel and fiber from rotating as the connectors are mated.
A typical connector is installed by preparing the fiber end and inserting it into the rear of the connector body. Quick-set adhesive is usually used to hold the fiber securely, and a strain relief is secured to the rear. Once the adhesive sets, the fiber's end is polished to a mirror finish. Various polish profiles are used, depending on the type of fiber and the application. For single-mode fiber, fiber ends are typically polished with a slight curvature that makes the mated connectors touch only at their cores. This is called a physical contact (PC) polish. The curved surface may be polished at an angle, to make an angled physical contact (APC) connection. Such connections have higher loss than PC connections, but greatly reduced back reflection, because light that reflects from the angled surface leaks out of the fiber core. The resulting signal strength loss is called gap loss. APC fiber ends have low back reflection even when disconnected.
In the 1990s, terminating fiber optic cables was labor-intensive. The number of parts per connector, polishing of the fibers, and the need to oven-bake the epoxy in each connector made terminating fiber optic cables difficult. Today, many connectors types are on the market that offer easier, less labor-intensive ways of terminating cables. Some of the most popular connectors are pre-polished at the factory, and include a gel inside the connector. Those two steps help save money on labor, especially on large projects. A cleave is made at a required length, to get as close to the polished piece already inside the connector. The gel surrounds the point where the two pieces meet inside the connector for very little light loss. Long term performance of the gel is a design consideration, so for the most demanding installations, factory pre-polished pigtails of sufficient length to reach the first fusion splice enclosure is normally the safest approach that minimizes on-site labor.

Free-space coupling

It is often necessary to align an optical fiber with another optical fiber, or with an optoelectronic device such as a light-emitting diode, a laser diode, or a modulator. This can involve either carefully aligning the fiber and placing it in contact with the device, or can use a lens to allow coupling over an air gap. Typically the size of the fiber mode is much larger than the size of the mode in a laser diode or a silicon optical chip. In this case a tapered or lensed fiber is used to match the fiber mode field distribution to that of the other element. The lens on the end of the fiber can be formed using polishing, laser cutting or fusion splicing.
In a laboratory environment, a bare fiber end is coupled using a fiber launch system, which uses a microscope objective lens to focus the light down to a fine point. A precision translation stage (micro-positioning table) is used to move the lens, fiber, or device to allow the coupling efficiency to be optimized. Fibers with a connector on the end make this process much simpler: the connector is simply plugged into a pre-aligned fiberoptic collimator, which contains a lens that is either accurately positioned with respect to the fiber, or is adjustable. To achieve the best injection efficiency into single-mode fiber, the direction, position, size and divergence of the beam must all be optimized. With good beams, 70 to 90% coupling efficiency can be achieved.
With properly polished single-mode fibers, the emitted beam has an almost perfect Gaussian shape—even in the far field—if a good lens is used. The lens needs to be large enough to support the full numerical aperture of the fiber, and must not introduce aberrations in the beam. Aspheric lenses are typically used.

Fiber fuse

At high optical intensities, above 2 megawatts per square centimeter, when a fiber is subjected to a shock or is otherwise suddenly damaged, a fiber fuse can occur. The reflection from the damage vaporizes the fiber immediately before the break, and this new defect remains reflective so that the damage propagates back toward the transmitter at 1–3 meters per second (4–11 km/h, 2–8 mph). The open fiber control system, which ensures laser eye safety in the event of a broken fiber, can also effectively halt propagation of the fiber fuse. In situations, such as undersea cables, where high power levels might be used without the need for open fiber control, a "fiber fuse" protection device at the transmitter can break the circuit to keep damage to a minimum.

Chromatic dispersion

The refractive index of fibers varies slightly with the frequency of light, and light sources are not perfectly monochromatic. Modulation of the light source to transmit a signal also slightly widens the frequency band of the transmitted light. This has the effect that, over long distances and at high modulation speeds, the different frequencies of light can take different times to arrive at the receiver, ultimately making the signal impossible to discern, and requiring extra repeaters. This problem can be overcome in a number of ways, including the use of a relatively short length of fiber that has the opposite refractive index gradient. 

                           Hasil gambar untuk electronic signal detector   


conclusion about signal tracer  :

Signal tracer


A signal tracer is a piece of electronic test equipment used to troubleshoot radio and other electronic circuitry.
Usually a very simple device, it normally provides an amplifier, and a loudspeaker, often battery-powered and packaged into a small, hand-held test probe. An optional diode detector is usually also provided, allowing the detection of amplitude-modulated signals.
The technician injects a test signal into the device under test. Then, by using the signal tracer, the tech can follow the signal through the various circuits of the radio receiver. So long as the signal can be heard, the circuitry up to that point is (at least minimally) functional. If the signal disappears, however, a fault can be assumed to be present in the stage of the circuit just passed.
The diode detector is only sensitive to amplitude modulation but even circuits that are normally used for other modulation schemes (such as FM radios) can be tested by using an AM test signal for testing the radio frequency circuits, then switching to an FM test signal (and switching out the diode detector) for testing the audio circuits of the radio.
More sophisticated signal tracers may display digital levels using, for example, LEDs. For long pulse trains, a cyclic redundancy check may be calculated and displayed, giving the tech insight into the content of circuits that are switching rapidly.

Test probe


Typical passive oscilloscope probe being used to test an integrated circuit

A test probe is a physical device used to connect electronic test equipment to a device under test (DUT). Test probes range from very simple, robust devices to complex probes that are sophisticated, expensive, and fragile. Specific types include test prods, oscilloscope probes and current probes. A test probe is often supplied as a test lead, which includes the probe, cable and terminating connector.

Voltage probes

Voltage probes are used to measure voltages present on the DUT. To achieve high accuracy, the test instrument and its probe must not significantly affect the voltage being measured. This is accomplished by ensuring that the combination of instrument and probe exhibit a sufficiently high impedance that will not load the DUT. For AC measurements, the reactive component of impedance may be more important than the resistive.

Simple test leads

A pair of simple test leads 

A typical voltmeter probe consists of a single wire test lead that has on one end a connector that fits the voltmeter and on the other end a rigid, tubular plastic section that comprises both a handle and probe body. The handle allows a person to hold and guide the probe without influencing the measurement (by becoming part of the electric circuit) or being exposed to dangerous voltages that might cause electric shock. Within the probe body, the wire is connected to a rigid, pointed metal tip that contacts the DUT. Some probes allow an alligator clip to be attached to the tip, thus enabling the probe to be attached to the DUT so that it need not be held in place.
Test leads are usually made with finely stranded wire to keep them flexible, of wire gauges sufficient to conduct a few amperes of electric current. The insulation is chosen to be both flexible and have a breakdown voltage higher than the voltmeter's maximum input voltage. The many fine strands and the thick insulation make the wire thicker than ordinary hookup wire.
Two probes are used together to measure voltage, current, and two-terminal components such as resistors and capacitors. When making DC measurements it is necessary to know which probe is positive and which is negative, so by convention the probes are colored red for positive and black for negative. Depending upon the accuracy required, they can be used with signal frequencies ranging from DC to a few kilohertz.
When sensitive measurements must be made (e.g., very low voltages, or very low or very high resistances) shields, guards, and techniques such as four-terminal Kelvin sensing (using separate leads to carry the measuring current and to sense the voltage) are used.

Tweezer probes

A tweezer probe
Tweezer probes are a pair of simple probes fixed to a tweezer mechanism, operated with one hand, for measuring voltages or other electronic circuit parameters between closely spaced pins.

Pogo pins

Spring probes (a.k.a. "pogo pins") are spring-loaded pins used in electrical test fixtures to contact test points, component leads, and other conductive features of the DUT (Device Under Test). These probes are usually press-fit into probe sockets, to allow their easy replacement on test fixtures which may remain in service for decades, testing many thousands of DUTs in automatic test equipment.

Oscilloscope probes

Oscilloscopes display the instantaneous waveform of varying electrical quantities, unlike other instruments which give numerical values of relatively stable quantities.
Scope probes fall into two main categories: passive and active. Passive scope probes contain no active electronic parts, such as transistors, so they require no external power.
Because of the high frequencies often involved, oscilloscopes do not normally use simple wires ("flying leads") to connect to the DUT. Flying leads are likely to pick up interference, so they are not suitable for low-level signals. Furthermore, the inductance of flying leads make them unsuitable for high frequency signals. Instead, a specific scope probe is used, which uses a coaxial cable to transmit the signal from the tip of the probe to the oscilloscope. This cable has two main benefits: it protects the signal from external electromagnetic interference, improving accuracy for low-level signals; and it has a lower inductance than flying leads, making the probe more accurate for high-frequency signals.
Although coaxial cable has lower inductance than flying leads, it has higher capacitance: a typical 50 ohm cable has about 90 pF per meter. Consequently, a one-meter high-impedance direct (1×) coaxial probe may load the circuit with a capacitance of about 110 pF and a resistance of 1 megohm.

Passive probes

A passive oscilloscope probe with a switch in the probe handle that selects 1× or 10× attenuation
To minimize loading, attenuator probes (e.g., 10× probes) are used. A typical probe uses a 9 megohm series resistor shunted by a low-value capacitor to make an RC compensated divider with the cable capacitance and scope input. The RC time constants are adjusted to match. For example, the 9 megohm series resistor is shunted by a 12.2 pF capacitor for a time constant of 110 microseconds. The cable capacitance of 90 pF in parallel with the scope input of 20 pF (total capacitance 110 pF) and 1 megohm also gives a time constant of 110 microseconds. In practice, there will be an adjustment so the operator can precisely match the low frequency time constant (called compensating the probe). Matching the time constants makes the attenuation independent of frequency. At low frequencies (where the resistance of R is much less than the reactance of C), the circuit looks like a resistive divider; at higher frequencies (resistance much greater than reactance), the circuit looks like a capacitive divider.
The result is a frequency compensated probe for modest frequencies that presents a load of about 10 megohms shunted by 12 pF. Although such a probe is an improvement, it does not work when the time scale shrinks to several cable transit times (transit time is typically 5 ns). In that time frame, the cable looks like its characteristic impedance, and there will be reflections from the transmission line mismatch at the scope input and the probe that causes ringing. The modern scope probe uses lossy low capacitance transmission lines and sophisticated frequency shaping networks to make the 10× probe perform well at several hundred megahertz. Consequently, there are other adjustments for completing the compensation.
A directly connected test probe (so called 1× probe) puts the unwanted lead capacitance across the circuit under test. For a typical coaxial cable, loading is of the order of 100pF per meter (the length of a typical test lead).
Attenuator probes minimize capacitive loading with an attenuator, but reduce the magnitude of the signal delivered to the instrument. A 10× attenuator will reduce the capacitive load by a factor of about 10. The attenuator must have an accurate ratio over the whole range of frequencies of interest; the input impedance of the instrument becomes part of the attenuator. A DC attenuator with resistive divider is supplemented with capacitors, so that the frequency response is predictable over the range of interest.
The RC time constant matching method works as long as the transit time of the shielded cable is much less than the time scale of interest. That means that the shielded cable can be viewed as a lumped capacitor rather than an inductor. Transit time on a 1-meter cable is about 5 ns. Consequently, these probes will work to a few megahertz, but after that transmission line effects cause trouble.
At high frequencies, the probe impedance will be low.
The most common design inserts a 9 megohm resistor in series with the probe tip. The signal is then transmitted from the probe head to the oscilloscope over a special lossy coaxial cable that is designed to minimize capacitance and ringing. The invention of this cable has been traced to John Kobbe, an engineer working for Tektronix. The resistor serves to minimize the loading that the cable capacitance would impose on the DUT. In series with the normal 1 megohm input impedance of the oscilloscope, the 9 megohm resistor creates a 10× voltage divider so such probes are normally known as either low cap(acitance) probes or 10× probes, often printed with the letter X or x instead of the multiplication sign, and usually spoken of as "a times-ten probe".
Because the oscilloscope input has some parasitic capacitance in parallel with the 1 megohm resistance, the 9 megohm resistor must also be bypassed by a capacitor to prevent it from forming a severe RC low-pass filter with the 'scope's parasitic capacitance. The amount of bypass capacitance must be carefully matched with the input capacitance of the oscilloscope so that the capacitors also form a 10× voltage divider. In this way, the probe provides a uniform 10× attenuation from DC (with the attenuation provided by the resistors) to very high AC frequencies (with the attenuation provided by the capacitors).
In the past, the bypass capacitor in the probe head was adjustable (to achieve this 10× attenuation). More modern probe designs use a laser-trimmed thick-film electronic circuit in the head that combines the 9 megohm resistor with a fixed-value bypass capacitor; they then place a small adjustable capacitor in parallel with the oscilloscope's input capacitance. Either way, the probe must be adjusted so that it provides uniform attenuation at all frequencies. This is referred to as compensating the probe. Compensation is usually accomplished by probing a 1 kHz square wave and adjusting the compensating capacitor until the oscilloscope displays the most square waveshape. Most oscilloscopes have a 1 kHz calibration source on their front panels since probe compensation must be done every time a 10:1 probe is attached to an oscilloscope input. Newer, faster probes have more complex compensation arrangements and may occasionally require further adjustments.
100× passive probes are also available, as are some designs specialized for use at very high voltages (up to 25 kV).
Passive probes usually connect to the oscilloscope using a BNC connector. Most 10× probes are equivalent to a load of about 10-15 pF and 10 megohms on the DUT, with 100× probes loading the circuit less.

Lo Z probes

Z0 probes are a specialized type of low-capacitance passive probe used in low-impedance, very-high-frequency circuits. They are similar in design to 10× passive probes but at much lower impedance levels. The probe cables usually have a characteristic impedance of 50 ohms and connect to oscilloscopes with a matched 50 ohm (rather than a 1 megohm) input impedance). High-impedance scope probes are designed for the conventional 1 megohm oscilloscope, but the 1 megohm input impedance is only at low frequency; the input impedance is not a constant 1 megohm across the probe's bandwidth but rather decreases with frequency. For example, a Tektronix P6139A input impedance starts falling above 10 kHz and is about 100 ohms at 100 MHz. A different probe technique is needed for high frequency signals.
A high frequency oscilloscope presents a matched load (usually 50 ohms) at its input, which minimizes reflections at the scope. Probing with a matching 50-ohm transmission line would offer high frequency performance, but it would unduly load most circuits. An attenuator (resistive divider) can be used to minimize loading. At the tip, these probes use a 450 ohm (for 10× attenuation) or 950 ohm (for 20× attenuation) series resistor. Tektronix sells a 10× divider probe with a 9 GHz bandwidth with a 450 ohm series resistor. These probes are also called resistive divider probes, since a 50 ohm transmission line presents a purely resistive load.
The Z0 name refers to the characteristic impedance of the oscilloscope and cable. The matched impedances provide better high-frequency performance than an unmatched passive probe can achieve, but at the expense of the low 500-ohm load offered by the probe tip to the DUT. Parasitic capacitance at the probe tip is very low so, for very high-frequency signals, the Z0 probe can offer lower loading than any hi-Z probe and even many active probes.
In principle this type of probe can be used at any frequency, but at DC and lower frequencies circuits often have high impedances that would be unacceptably loaded by the probe's low 500 or 1000 ohm probe impedance. Parasitic impedances limit very-high-frequency circuits to operating at low impedance, so the probe impedance is less of a problem.

Active scope probes

Active scope probes use a high-impedance high-frequency amplifier mounted in the probe head, and a screened lead. The purpose of the amplifier is not gain, but isolation (buffering) between the circuit under test and the oscilloscope and cable, loading the circuit with only a low capacitance and high DC resistance, and matching the oscilloscope input. Active probes are commonly seen by the circuit under test as a capacitance of 1 picofarad or less in parallel with 1 megohm resistance. Probes are connected to the oscilloscope with a cable matching the characteristic impedance of the oscilloscope input. Tube based active probes were used before the advent of high-frequency solid-state electronics, using a small vacuum tube as cathode follower amplifier.
Active probes have several disadvantages which have kept them from replacing passive probes for all applications:
  • They are several times more expensive than passive probes.
  • They require power (but this is usually supplied by the oscilloscope).
  • Their dynamic range is limited, sometimes as low as 3 to 5 volts, and they can be damaged by overvoltage, either from the signal or electrostatic discharge.
Many active probes allow the user to introduce an offset voltage to allow measurement of voltages with excessive DC level. The total dynamic range is still limited, but the user may be able to adjust its centerpoint so that voltages in the range of, for example, zero to five volts may be measured rather than -2.5 to +2.5.
Because of their inherent low voltage rating, there is little need to provide high-voltage insulation for operator safety. This allows the heads of active probes to be extremely small, making them very convenient for use with modern high-density electronic circuits.
Passive probes and a modest active probe design is discussed in an application note by Williams.
The Tektronix P6201 is an early DC to 900 MHz active FET probe.
At extreme high frequencies a modern digital scope requires that the user solder a preamp to the DUT to get 50GS/s, 20 GHz performance.

Differential probes

Differential probes are optimized for acquiring differential signals. To maximize the common-mode rejection ratio (CMRR), differential probes must provide two signal paths that are as nearly identical as possible, matched in overall attenuation, frequency response, and time delay.
In the past, this was done by designing passive probes with two signal paths, requiring a differential amplifier stage at or near the oscilloscope. (A very few early probes fitted the differential amplifier into a rather-bulky probe head using vacuum tubes.) With advances in solid-state electronics, it has become practical to put the differential amplifier directly within the probe head, greatly easing the requirements on the rest of the signal path (since it now becomes single-ended rather than differential and the need to match parameters on the signal path is removed). A modern differential probe usually has two metal extensions which can be adjusted by the operator to simultaneously touch the appropriate two points on the DUT. Very high CMRRs are thereby made possible.

Additional probe features

All scope probes contain some facility for grounding (earthing) the probe to the circuit's reference voltage. This is usually accomplished by connecting a very short pigtail wire from the probe head to ground. Inductance in the ground wire can lead to distortion in the observed signal, so this wire is kept as short as possible. Some probes use a small ground foot instead of any wire, allowing the ground link to be as short as 10 mm.
Most probes allow a variety of "tips" to be installed. A pointed tip is the most common, but a seizer probe or "test hook" with a hooked tip that can secure to the test point, is also commonly used. Tips that have a small plastic insulating foot with indentations into it can make it easier to probe very-fine-pitch integrated circuits; the indentations mate with the pitch of the IC leads, stabilizing the probe against the shaking of the user's hand and thereby help to maintain contact on the desired pin. Various styles of feet accommodate various pitches of the IC leads. Different types of tips can also be used for probes for other instruments.
Some probes contain a push button. Pressing the button will either disconnect the signal (and send a ground signal to the 'scope) or cause the 'scope to identify the trace in some other way. This feature is very useful when simultaneously using more than one probe as it lets the user correlate probes and traces on the 'scope screen.
Some probe designs have additional pins surrounding the BNC or use a more complex connector than a BNC. These extra connections allow the probe to inform the oscilloscope of its attenuation factor (10×, 100×, other). The oscilloscope can then adjust its user displays to automatically take into account the attenuation and other factors caused by the probe. These extra pins can also be used to supply power to active probes.
Some ×10 probes have a "×1/×10" switch. The "×1" position bypasses the attenuator and compensating network, and can be used when working with very small signals that would be below the scope's sensitivity limit if attenuated by ×10.

Interchangeability

Because of their standardized design, passive probes (including Z0 probes) from any manufacturer can usually be used with any oscilloscope (although specialized features such as the automatic readout adjustment may not work). Passive probes with voltage dividers may not be compatible with a particular scope. The compensation adjustment capacitor only allows for compensation over a small range of oscilloscope input capacitance values. The probe compensation range must be compatible with the oscilloscope input capacitance.
On the other hand, active probes are almost always vendor-specific due to their power requirements, offset voltage controls, etc. Probe manufacturers sometimes offer external amplifiers or plug-in AC power adapters that allow their probes to be used with any oscilloscope.

High-voltage probes

High voltage resistor divider probe 

A high voltage probe allows an ordinary voltmeter to measure voltages that would otherwise be too high to measure or even destructive. It does this by reducing the input voltage to a safe, measurable level with a precision voltage divider circuit within the probe body.
Probes intended for up to 100 kV typically employ a resistor voltage divider, with an input resistance of hundreds or thousands of megohms to minimize circuit loading. High linearity and accuracy is achieved by using resistors with extremely low voltage coefficients, in matched sets that maintain a consistent, precise divider ratio across the probe's operating temperature. Voltmeters have input resistance that effectively alters the probe's divider ratio, and parasitic capacitance that combines with the probe's resistance to form an RC circuit; these can easily reduce DC and AC accuracy, respectively, if left uncompensated. To mitigate these effects, voltage divider probes usually include additional components that improve frequency response and allow them to be calibrated for different meter loads.
Even higher voltages can be measured with capacitor divider probes, though the larger physical size and other mechanical features (e.g., corona rings) of these devices often preclude their use as handheld probes.

Current probes

A current probe generates a voltage proportional to a current in the circuit being measured; as the proportionality constant is known, instruments that respond to voltage can be calibrated to indicate current. Current probes can be used both by measuring instruments and oscilloscopes.

Sampling resistor

The classic current probe is a low valued resistor (a "sampling resistor" or "current shunt") inserted in the current's path. The current is determined by measuring the voltage drop across the resistor and using Ohm's law. (Wedlock & Roberge 1969, p. 152.) The sampling resistance needs to be small enough not to affect circuit operation significantly, but large enough to provide a good reading. The method is valid for both AC and DC measurements. A disadvantage of this method is the need to break the circuit to introduce the shunt. Another problem is measuring the voltage across the shunt when common-mode voltages are present; a differential voltage measurement is needed.

Alternating current probes

Stromwandler Zeichnung.svg
Alternating currents are relatively easy to measure as transformers can be used. A current transformer is commonly used to measure alternating currents. The current to be measured is forced through the primary winding (often a single turn) and the current through the secondary winding is found by measuring the voltage across a current-sense resistor (or "burden resistor"). The secondary winding has a burden resistor to set the current scale. The properties of a transformer offer many advantages. The current transformer rejects common mode voltages, so an accurate single-ended voltage measurement can be made on a grounded secondary. The effective series resistance R_s of the primary winding is set by the burden resistor on the secondary winding R and the transformer turns ratio N, where: R_s = R / N^2.
The core of some current transformers is split and hinged; it is opened and clipped around the wire to be sensed, then closed, making it unnecessary to free one end of the conductor and thread it through the core.
Another clip-on design is the Rogowski coil. It is a magnetically balanced coil that measures current by electronically evaluating the line integral around a current.
High-frequency, small-signal, passive current probes typically have a frequency range of several kilohertz to over 100 MHz. The Tektronix P6022 has a range from 935 Hz to 200 MHz. (Tektronix 1983, p. 435)

Direct-current probes

Transformers cannot be used to probe direct currents (DC).
Some DC probe designs use the nonlinear properties of a magnetic material to measure DC.
Other current probes use Hall effect sensors to measure the magnetic field around a wire produced by an electric current through the wire without the need to interrupt the circuit to fit the probe. They are available for both voltmeters and oscilloscopes. Most current probes are self-contained, drawing power from a battery or the instrument, but a few require the use of an external amplifier unit.

Hybrid AC/DC current probes

More advanced current probes combine a Hall effect sensor with a current transformer. The Hall effect sensor measures the DC and low frequency components of the signal and the current transformer measures the high frequency components. These signals are combined in the amplifier circuit to yield a wide band signal extending from DC to over 50 MHz. (Wedlock & Roberge 1969, p. 154) The Tektronix A6302 current probe and AM503 amplifier combination is an example of such a system. (Tektronix 1983, p. 375) (Tektronix 1998, p. 571)

Near-field probes

Near-field probes allow the measurement of an electromagnetic field. They are commonly used to measure electrical noise and other undesirable electromagnetic radiation from the DUT, although they can also be used to spy on the workings of the DUT without introducing much loading into the circuitry.
They are commonly connected to spectrum analyzers.

Temperature probes

A thermocouple probe
Temperature probes are used to make contact measurements of surface temperatures. They employ a temperature sensor such as a thermistor, thermocouple, or RTD, to produce a voltage that varies with temperature. In the case of thermistor and RTD probes, the sensor must be electrically stimulated to produce a voltage, whereas thermocouple probes do not require stimulation because a thermocouple will independently produce an output voltage.
Voltmeters can sometimes be used to measure temperature probes, but this task is usually delegated to specialized instruments that will stimulate the probe's sensor (if necessary), measure the probe's output voltage, and convert the voltage to temperature units.

Demodulator probes

To measure or display the modulating waveform of a modulated high-frequency signal—for example, an amplitude-modulated radio signal—a probe fitted with a simple diode demodulator can be used. The probe will output the modulating waveform without the high-frequency carrier.